EINHELL TC-EN 20 E User Manual

GB
- 15 -
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ..................... 79,1 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ....................... 90,1 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
h
= 2.786 m/s
2
K uncertainty = 1.5 m/s
2
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Inserting the staples and nails (Fig. 2-4)
•
Press the magazine slide (4) together using
your thumb and index finger.
•
Always pull out the magazine slide towards
the rear. (See Fig. 2)
•
Fill the magazine with staples or nails as
shown in Fig. 3 and 4. With the nails, make
sure that these rest against the left inner side
(5) of the magazine.
•
Then push the magazine slide back in until it
snaps noticeably into place.
Important!
It must be possible to move the magazine slide
without applying much force. Watch out for jam-
med staples and nails.
5.2 Filling level indicator (Fig. 1)
The fi lling level indicator (6) shows you if there are
still enough staples or nails in the magazine (5).
If necessary, refi ll the magazine (5) as described
above. Avoid operating the trigger (1) if there are
no staples or nails in the magazine (5).
Anl_TC_EN_20_E_SPK1.indb 15Anl_TC_EN_20_E_SPK1.indb 15 08.11.2016 11:10:5808.11.2016 11:10:58

EINHELL TC-EN 20 E Specifications

General

Power source	AC
AC input voltage	220-240 V
AC input frequency	50 Hz
Pinning	No
Product color	Black, Red
Stapling capacity	- sheets
Permanent stapling	Yes
Number of staples included	1000 pc(s)

Weight and Dimensions

Weight	1090 g
Package depth	277 mm
Package width	71 mm
Package height	198 mm
Package weight	1570 g