EINHELL TC-MX 1400-2 E Original Operating Instructions

GB
- 15 -
4. Technical data
Mains voltage: .........................220-240 V~ 50 Hz
Power input: ............................................ 1400 W
Idling speed: ...........................0-480 / 0-780 min
-1
Mixing tool mount: ........................................ M14
Protection class: ............................................ II/

Weight: .....................................................3.19 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
pA
sound pressure level ..................... 88.6 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ....................... 99.6 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Right handle
Vibration emission value a
h
= 0.718 m/s
2
K uncertainty = 1.5 m/s
2
Left handle
Vibration emission value a
h
= 1.146 m/s
2
K uncertainty = 1.5 m/s
2
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Mixer assembly (Fig. 2-3):
First scew mixer part (6a) together with mixer part
(6b). Screw the mixer (6) into the mixer holder (4)
afterwards. Use the two spanners to do this. Use
one of the spanners (7a) to hold the mixer holder
(4) in place and then use the second spanner (7b)
to tighten up the mixer (6). Proceed in the reverse
sequence to undo the mixer.
is secure (pull the mains plug).
Anl_TC_MX_1400_2_E_SPK9.indb 15Anl_TC_MX_1400_2_E_SPK9.indb 15 09.03.2021 06:55:4609.03.2021 06:55:46

EINHELL TC-MX 1400-2 E Specifications

General

Input power	1400 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Idle speed	780 RPM
Torque (max)	- N⋅m
Maximum stirrer diameter	133 mm
Package depth	345 mm
Package width	675 mm
Package height	230 mm
Package weight	6070 kg
Best uses	Mortar, Paint
Chuck type	-
Soft start	Yes
Product color	Red
Spindle thread	M14
Number of speeds	2

Weight and Dimensions

Width	325 mm
Height	210 mm
Weight	3460 g