EINHELL TC-MX 1400-2 E User Manual

GB
- 15 -
4. Technical data
Mains voltage: .........................220-240 V~ 50 Hz
Power input: ............................................ 1400 W
Idling speed: ...........................0-480 / 0-780 min
-1
Mixing tool mount: ........................................ M14
Protection class: ............................................ II/

Weight: .....................................................3.19 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ..................... 88.6 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ....................... 99.6 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Right handle
Vibration emission value a
h
= 0.718 m/s
2
K uncertainty = 1.5 m/s
2
Left handle
Vibration emission value a
h
= 1.146 m/s
2
K uncertainty = 1.5 m/s
2
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Mixer assembly (Fig. 2-3):
First scew mixer part (6a) together with mixer part
(6b). Screw the mixer (6) into the mixer holder (4)
afterwards. Use the two spanners to do this. Use
one of the spanners (7a) to hold the mixer holder
(4) in place and then use the second spanner (7b)
to tighten up the mixer (6). Proceed in the reverse
sequence to undo the mixer.
is secure (pull the mains plug).
Anl_TC_MX_1400_2_E_SPK7.indb 15Anl_TC_MX_1400_2_E_SPK7.indb 15 30.07.15 14:5730.07.15 14:57

EINHELL TC-MX 1400-2 E Specifications

General

Input power	1400 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Idle speed	780 RPM
Torque (max)	- N⋅m
Maximum stirrer diameter	133 mm
Package depth	345 mm
Package width	675 mm
Package height	230 mm
Package weight	6070 kg
Best uses	Mortar, Paint
Chuck type	-
Soft start	Yes
Product color	Red
Spindle thread	M14
Number of speeds	2

Weight and Dimensions

Width	325 mm
Height	210 mm
Weight	3460 g