EINHELL TC-SY 400 P - User Manual

Questions and Answers

R
Rachel GloverAug 14, 2025
Why is no material exiting from my EINHELL TC-SY 400 P nozzle?
- J
  Jennifer JacksonAug 14, 2025
  Several issues could be the cause. The nozzle or material tube might be clogged and need cleaning. The max paint volume control may be rotated too far anti-clockwise, so turn it clockwise. The material tube could be loose, so insert it properly. There might not be enough pressure build-up in the container, so tighten the container. Finally, the material's consistency might be too thick, requiring dilution.
R
Roy MorrisonAug 17, 2025
What to do if material drips from the nozzle of my EINHELL TC-SY 400 P Paint Sprayer after spraying?
- B
  buckbrandonAug 17, 2025
  If your EINHELL Paint Sprayer drips after spraying, the nozzle may be loose and needs tightening, or the nozzle or nozzle seal may be worn and require replacement. Also, check for solids in the air cap or nozzle and clean them.
W
William StoneAug 20, 2025
Why is the atomization too coarse with my EINHELL TC-SY 400 P?
- R
  Richard ChapmanAug 20, 2025
  Coarse atomization can occur if the material viscosity or volume is too high, so dilute the material or turn the max. paint volume control anti-clockwise. A dirty nozzle or insufficient pressure build-up in the container can also cause this.
R
Ryan OrozcoAug 25, 2025
Why is there excessive spray mist when using my EINHELL TC-SY 400 P?
- J
  Julie BanksAug 25, 2025
  Excessive spray mist can occur if the gun is held too far from the object. Hold the gun closer. Also, turn the max. paint volume control anti-clockwise.
S
Sandra PerezAug 27, 2025
What to do if the coating pattern is too light and uneven with my EINHELL TC-SY 400 P?
- J
  jeanpowellAug 27, 2025
  If the coating pattern is too light and uneven, it might be because you are moving the paint spray gun too fast across the surface. Try moving the gun more slowly.
W
wrightcodyAug 31, 2025
Why does the paint run or sag when using my EINHELL Paint Sprayer?
- S
  Shane JuarezAug 31, 2025
  Paint running or sagging indicates that you've applied too much material. To fix this, turn the max. paint volume control anti-clockwise.
X
xporterSep 3, 2025
Why is my EINHELL TC-SY 400 P Paint Sprayer spray intermittent (“fluttering”)?
- B
  breanna89Sep 3, 2025
  An intermittent or fluttering spray often means that almost all of the material in the container has been used up. Simply add more material.
N
Nathaniel RogersSep 6, 2025
How to fix EINHELL Paint Sprayer when no material exits from the nozzle?
- C
  Claudia HensonSep 6, 2025
  If the EINHELL Paint Sprayer isn't spraying material, several issues could be the cause. First, check if the nozzle or material tube is clogged and clean them. Ensure the max paint volume control isn't rotated too far anti-clockwise; turn it clockwise. Also, verify the material tube is secure and the container is tightened to build pressure. Finally, if the material is too thick, dilute it.
N
Nicole Clark MDSep 10, 2025
Why is the atomization too coarse on my EINHELL TC-SY 400 P Paint Sprayer?
- S
  Sabrina McconnellSep 10, 2025
  If the atomization is too coarse with your EINHELL Paint Sprayer, it could be due to several reasons. The material viscosity might be too high, so try diluting it. Alternatively, the material volume could be too high; turn the max paint volume control anti-clockwise. A dirty nozzle or insufficient pressure in the container (tighten the container) could also be the cause. In some cases, the max. paint volume control is turned too far clockwise and needs cleaning.

Summary

Safety Regulations

Proper Use

Residual Risks

Before Starting the Equipment

Operation

Spray Gun Assembly

Material Preparation & Nozzle Selection

Details preparing paint, viscosity measurement, and nozzle diameter selection.

Working with the Paint Spray Gun

Provides instructions on how to hold, use, and adjust the spray gun for effective spraying.

Adjusting the Fan Pattern

Explains how to set the spray gun to produce different fan patterns for various surfaces.

Spraying Techniques

Cleaning, Maintenance, and Spare Parts

Cleaning

Details the process for cleaning the spray gun, including disassembly and flushing.

Disconnecting and Cleaning the Gun

Step-by-step guide to disassemble and clean the spray gun after use.

Troubleshooting Guide

Service Information

Reporting Defects or Faults

EINHELL TC-SY 400 P Specifications

General

AC input voltage	220-240 V
AC input frequency	50 Hz
Capacity	0.8 L
Product color	Black, Red
Spray gun purpose	Paint
Package depth	128 mm
Package width	275 mm
Package height	256 mm
Package weight	1850 g