EINHELL TE-AP 950 E User Manual

GB
- 7 -
Additional Safety rules
•
Always check the saw, the power cable and
the plug before use. Only ever use the saw if it
is in perfect, undamaged condition. Damaged
parts have to be repaired or replaced immedi-
ately by a qualified electrician.
•
Always pull the plug out of the power socket
before carrying out any work on the saw,
before changing the blade and in periods of
non-use.
•
Always run the power cable away from the
back of the saw to guard it from damage.
•
For outdoors work use only suitably approved
extension cables with a minimum conductor
cross section of 1,5 mm
2
. The plug connec-
tors must have earthing contacts and be
splash-proof.
•
Keep the saw in a safe place and out of the
reach of children.
•
Always wear goggles, safety gloves and ear
muffs when sawing. Wear a breathing mask
on dusty jobs.
•
Never leave any keys or adjustment spanners
in position on the saw. Before switching on,
check that all keys and adjustment spanners
have been removed.
•
Secure the workpiece (with a clamp) so that it
cannot slip.
•
It is prohibited to use the saw on asbes-
tos materials. Please note the accident
prevention regulations in force in your country.
•
Use only original spare parts.
•
Repairs are to be carried out by qualified
electricians only.
•
The level of noise at the workplace may ex-
ceed 85 dB(A). In this case you will need to
introduce noise protection measures for the
user.
•
Make sure of your footing. Avoid abnormal
working positions.
•
Keep your electric tool out of the rain. Never
use electric tools in wet or damp conditions,
and never use them near inflammable liquids.
•
Never carry the electric tool by its power
cable. Keep the power cable safe from dama-
ge. Oil, solvent and sharp edges can damage
cables.
•
Keep your workplace tidy.
•
Make sure the power switch is off before in-
serting the plug in the socket.
•
Wear suitable clothing. Never wear loose-
fitting clothes or jewelry. Use a hair-net on
long hair.
•
For your own safety, use only the
manufacturer’s accessories and attachments.
•
Use only sharp saw blades that are in perfect
condition. Replace bent and cracked saw bla-
des immediately.
•
After switching off the saw, do not press
against the side of the blade to bring it to a
halt.
•
Always cut at a steady rate of progress. This
will prevent accidents and prolong the life of
your saw and the blade.
•
Use only a damp cloth to clean your saw. Do
not use any aggressive agents for cleaning
purposes.
•
Check your saw to ensure that it is in good
working order. If the saw fails to work properly,
have it checked. Leave all maintenance and
inspection work strictly to a qualified electrici-
an or ISC GmbH.
•
Hold the equipment by the insulated
handles when carrying out work during
which the plug-in tool could strike con-
cealed power cables or its own mains
lead. Contact with a live cable can also make
the metal parts of the equipment live and will
cause an electric shock.
•
Use clamps or some other means to fas-
ten and secure the workpiece to a sturdy
surface. If you hold the workpiece only with
your hand or against your body it will remain
unstable and might cause you to lose control.
Do not lose these safety instructions
SiHi_Universalsaege_SPK13.indb 7SiHi_Universalsaege_SPK13.indb 7 23.02.2021 15:09:4323.02.2021 15:09:43

EINHELL TE-AP 950 E Specifications

General

Product color	Black, Red
Input power	950 W
Power source	AC
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Stroke length	28 mm
Cutting depth in wood	200 mm
Cutting depth in steel	20 mm
Speed control type	Electronic

Weight and Dimensions

Width	95, 492 mm
Height	201 mm
Weight	3194 g