EINHELL TE-CC 250 UF User Manual

TE-CC 250 UF
Art.-Nr.: 43.405.39 I.-Nr.: 11019
9
D Originalbetriebsanleitung
Tischkreissäge
GB Original operating instructions
Bench-type circular saw
F Instructions d’origine
Scie circulaire à table
I Istruzioni per l’uso originali
Sega circolare da banco
DK/ Original betjeningsvejledning
N Bordrundsav
CZ Originální návod k obsluze
Stolní kotoučová pila
SK Originálny návod na obsluhu
Stolná kotúčová píla
NL Originele handleiding
Tafelcirkelzaag
E Manual de instrucciones original
Sierra circular de mesa
RUS Оригинальное руководство по
эксплуатации
Дисковая пила со столом
SLO Originalna navodila za uporabo
Namizna krožna žaga
H Eredeti használati utasítás
Asztalikörfűrész
Anl_TE_CC_250_UF_SPK9.indb 1Anl_TE_CC_250_UF_SPK9.indb 1 15.10.2019 15:24:3615.10.2019 15:24:36

EINHELL TE-CC 250 UF Specifications

General

Idle speed	4500 RPM
Cutting depth (45º)	53 mm
Cutting depth (90º)	78 mm
On/off switch	Yes
Product color	Red, Stainless steel
Input power	1500 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz

Weight and Dimensions

Height	850 mm
Table depth	530 mm
Table width	645 mm
Blade diameter	250 mm
Blade thickness	30 mm
Height adjustment range	0 - 78 mm

Summary

1. Safety regulations

3. Proper use

4. Technical data

5. Before starting the equipment

6. Assembly

6.1 Fitting the table length extension (Fig. 2a, 2b)

6.2 Fitting the base frame (Fig. 1, 3-5)

6.3 Fitting and adjusting the splitter (Fig. 6a, 9)

6.4 Fitting/removing the saw blade guard (Fig. 6b, 1c)

6.6 Fitting/replacing the saw blade (Fig. 8)

7. Using the saw

7.1. ON/OFF switch (Fig. 1, 16 / Item 11)

7.3.1. Stop height (Fig. 11-14)

How to set the parallel stop's height based on workpiece thickness and guide face selection.

7.3.2. Cutting width (Fig. 12-14)

Adjusting the parallel stop to set the desired cutting width using the scale.

7.3.3. Setting the stop length (Fig. 12-14)

Adjusting the parallel stop rail length to prevent workpiece jamming during cuts.

7.4. Cross stop (Figure 15)

Instructions for installing and setting the cross stop for accurate angled cuts.

7.5. Setting the angle (Fig. 16)

8. Operation

8.1.1 Making longitudinal cuts (Figure 17)

Guide for performing longitudinal (slitting) cuts along the grain of wood.

8.1.2. Cutting narrow workpieces (Fig. 18)

Safety techniques for cutting narrow workpieces, emphasizing the use of a push stick.

8.1.3.Cutting extremely narrow workpieces (Fig. 19)

Specific advice for cutting very narrow workpieces, including using the low guide face of the parallel stop.

8.1.4. Making bevel cuts (Fig. 16/20)

Steps for making angled (bevel) cuts, including parallel stop positioning.

8.1.5. Making cross cuts (Fig. 21)

8.1.6 Working with the slide (Fig. 22a, 22b)

10. Cleaning, maintenance and ordering of spare parts