EINHELL TE-CD 18 Li User Manual

GB
- 8 -
4. Technical data
.c.d V 81........................................ ylppus egatloV
Idling speed: ............................0-320/0-1350 rpm
Torque settings: ........................................... 23+1
Forward and reverse rotation ..........................yes
Chuck clamping width ....................... max. 13 mm
Battery charger output voltage: ........10-21 V d. c.
Battery charger output current: ....................... 3 A
Mains voltage for charger ...200-260 V ~ 50-60 Hz
Battery type: .......................................Lithium-ion
Number of battery cells: .................................... 5
Battery capacitance: ................................. 3.0 Ah
Weight.........................................................1.7 kg
Max. screw diameter: .................................. 6 mm
-am eht setacidni retemaid wercs mumixam ehT
ximum diameter of the screw that can be screwed
into wood. The screw diameter can vary depen-
ding on the type of wood.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ..................... 68,9 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ....................... 79,9 dB(A)
K
WA
uncertainty ............................................. 3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Drilling in metal
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Screwing without hammer action
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
-row tcefrep ni era hcihw secnailppa esu ylnO
king order.
•
.ylraluger ecnailppa eht naelc dna ecivreS
•
.ecnailppa eht tius ot elyts gnikrow ruoy tpadA
•
.ecnailppa eht daolrevo ton oD
•
-en revenehw decivres ecnailppa eht evaH
cessary.
•
.esu ni ton si ti nehw ffo ecnailppa eht hctiwS
•
.sevolg evitcetorp raeW
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Anl_TE_CD_18_Li_Kit_SPK7.indb 20 04.06.13 12:04

EINHELL TE-CD 18 Li Specifications

General

Soft grip	Yes
Product design	Pistol grip drill
Number of gears	2
Torque settings	24
Screw diameter (max)	10 mm
Idle speed (1st gear)	320 RPM
Idle speed (2nd gear)	1350 RPM
Maximum torque (hard applications)	48 N⋅m
Product color	Black, Red
Number of batteries included	1 pc(s)
Power source	Battery
Charging time	30 min
Battery voltage	18 V
Battery capacity	1.5 Ah

Weight and Dimensions

Depth	420 mm
Width	105 mm
Height	335 mm
Weight	1500 g