GB
- 8 -
3. Before you begin to screw in walls and ma-
sonry, check for concealed electric wiring,
gas pipes and water pipes.
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(6) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
6.2 Changeover switch (Fig. 4/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
6.3 On/Off switch (Fig. 4 / Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless
screwdriver.
To switch on:
Press the On/Off switch (4).
To switch off :
Release the ON/OFF switch (4)
6.4 Battery capacity indicator (Fig. 5 – Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6.5 LED lamp (Fig. 6/Item 7)
The LED lamp (7) can be used in poor lighting
conditions to illuminate the area where you want
to screw. The LED light (7) will come on automati-
cally as soon as you press the On/Off switch (4).
6.6 Changing the bit (Fig. 7)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
Inserting the bit:
•
Insert the bit into the bit mount (1) as far as
the stop while simultaneously pulling the slee-
ve on the bit mount (1) toward the bit.
•
Release the sleeve again.
•
Check that the bit is securely seated.
Removing the bit:
•
Pull the sleeve on the bit mount (1) toward the
bit, hold it tight and remove the bit.
6.7 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw.
Anl_TE_CI_18_1_Li_4257239_SPK7.indb 8Anl_TE_CI_18_1_Li_4257239_SPK7.indb 8 13.12.2023 10:05:5713.12.2023 10:05:57
To Next Page
Loading...
Need help?
General
Weight and Dimensions
