GB
- 15 -
5. Before starting the equipment
Observe point 1 - Safety information.
Controls (buttons) (Fig. 2)
10 Desired Temperature + / Time Preselection +
11 Function Selection
12 On/Standby
13 Desired Temperature - / Time Preselection -
14 Time Preselection
Inserting batteries (Fig. 3-4):
1. Open the battery compartment cover by
pressing the lock (A) towards the middle and
pulling the battery compartment out at the
same time.
2. Insert the battery (B) in the battery compart-
ment with the positive pole facing down.
3. Press the battery compartment cover into the
remote control.
As the end user you are legally required to return
spent batteries. You can hand them in at public
collection points provided by your council or sales
outlets where batteries of this type are sold.
6. Operation
Warning! Before using the equipment for the fi rst
time, check that the voltage supply is the same as
the voltage details set out on the rating plate.
•
Read the safety regulations in section 1.
•
When the equipment is used for the first time
or after a long period of rest, it may emit an
odor for a short time. This is not a fault.
All modes and functions can be set using the but-
tons on the appliance as well as with the remote
control. The remote control requires a CR 2032
button cell (included in delivery).
6.1 Switching on the appliance
The ON/OFF main switch (Fig. 1 / Item 4) is used
to disconnect the equipment completely from the
mains supply.
The fi rst step when you want to use the appliance
is to turn on the main switch; the last step when
you no longer need the appliance is to turn off the
main switch. After the main switch is switched on,
the equipment will be in standby mode.
The heater shows the current equipment tem-
perature. The time display (00:00) for the timer
fl ashes.
6.2 Heating mode (Fig. 2)
With the On / Standby button (Item 12) you can
switch the equipment on or to standby mode.
Press the On / Standby button (12) to switch on
the equipment. The desired temperature (default
setting 38°C) fl ashes. The current equipment tem-
perature is then shown in the display, along with
the „Low heat output“ and „Blower“ symbols.
The time display (00:00) fl ashes briefl y and then
shows the operating time which has elapsed.
The heater operates with low heat output and the
blower.
Press the „Mode“ button (11) and by so doing
select the heating function in the following se-
quence.
Low heat output -> High heat output and blower
-> Frost protection function -> Low heat output
and blower -> Low heat output, etc.
6.3 Setting the desired temperature.
A desired temperature can be set between
5°C – 38°C, which is the temperature range of the
integrated temperature sensor (equipment tem-
perature). Press the „+“ or „-“ button to increase or
reduce the desired temperature.
For the equipment to heat, the desired tempera-
ture must be set higher than the indicated equip-
ment temperature. If the desired temperature is
exceeded by 2°C, the equipment will switch off
again.
In the frost protection function the temperature
is set to a default setting of 7°C and cannot be
adjusted.
6.4 Timer (Fig. 2)
Once you have fi rst set the desired heating mode
and the desired temperature, you can program
a time for switching on („ON“) or a time for swit-
ching off („OFF“). You can select from between
1min to 23h 59min. It is also possible to combine
the switch-on time with the switch-off time.
Press the „Clock“ button (14) and select the timer
function in the following sequence.
Switch-on time hour -> Switch-on time minute ->
Switch-off time hour -> Switch-off time minute ->
Continuous operation
Anl_WW_2000_R_SPK7.indb 15Anl_WW_2000_R_SPK7.indb 15 13.03.15 09:3413.03.15 09:34
To Next Page
Loading...
Need help?
General
