Elation ChaseBar User Manual

Product Descriptions
This is a T-bar 4 channels chaser, features 17 built-in chase patterns and 7 fixed scenes,
each pattern has four operating modes: Audio, Fast, Medium and Slow. When linkup, this unit
can be used as a either a Master or Slave. A DMX controller or a foot controller(supplied) can
be used to control this unit after proper connection.
24-004-1535
Rev 1.0
User Instructions
1. Channel Output: 5A/CH., Total 15A max.
2. Channel Fuse: F6A 250V 5x20mm
3. Blackout Selector: Moving this slider will enable or disable Stand by function when power is
. switched on.
4. Linkup Selector: Move this slider to select between Master and Slave.
5. Function Selector: This slider is used to select Audio/Fast/Medium/Slow mode for the patterns.
6. Channel LEDs: These LEDs indicate the intensity of corresponding channel or activity of the
pattern or scene.
7. Stand By Button: This button serves several functions. In Master mode, tap this button to
activate or deactivate Stand By(its LED flashes when Stand By is active).
Pressing this button for three seconds can activate 17 chase patterns or 7
fixed scenes. When chase patterns are activated, each tap of Pattern button
will select a chase pattern. When the scenes are activated, each tap of Pattern
button will forward a scene step by step.
8. Pattern Button: In Master mode, use this button to select chase pattern or scene.
9. Power Cable: AC 120V~60Hz, 15 A max.
10. Link In: In Master mode, this connector can be plugged in a foot controller(supplied) for
remote control. In DMX mode, this connector is used to receive an incoming
DMX signal from either a DMX controller or Link out(11) on another unit.
11. Link Out: This connector can be used to link to next unit.
Control & Functions
N'OUVREZ PAS..RISQUE DE CHOCELECTRIQUE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
THIS APPARATUS MUST BE EARTHED
POWER INPUT:
AC 120V~60Hz,15A MAX.
OUTPUT:
5A / Channel
Total 15A MAX.
Made in PRC
LINK OUTLINK IN
1 = Ground
2 = Data-
3 = Data+
43
2
1
FUSES
4
32
1
OUTPUT: 5A/CH, TOTAL 15A Max.
F6A 250V(5x20mm)
Monitor
PATTERN STAND BY
ON
Stand by
Master
Slave
Audio
Fast
Medium
Slow
Function
Linkup Select
1 2
34
5
6
789 10 11

Elation ChaseBar Specifications

General

Beam Angle	25°
Housing	Aluminum
Protection Rating	IP20
Control Protocol	DMX512
DMX Modes	6-channel
Input	DMX In
Power Supply	100-240V AC, 50/60Hz
DMX Channels	6
Type	LED Bar
Weight	15.0 lbs (6.8 kg)
Light Source	LED

Summary

Product Descriptions

Control & Functions

Channel Output

5A/CH., Total 15A max.

Channel Fuse

F6A 250V 5x20mm.

Blackout Selector

Enable or disable Stand by function when power is switched on.

Linkup Selector

Move this slider to select between Master and Slave.

Function Selector

Select Audio/Fast/Medium/Slow mode for the patterns.

Channel LEDs

Indicate intensity of corresponding channel or activity.

Stand By Button

Activate/deactivate Stand By; activate chase patterns or scenes.

Pattern Button

Select chase pattern or scene.

Power Cable

AC 120V~60Hz, 15A max.

Link In

Connect foot controller or receive DMX signal.

Link Out

Link to next unit.

About the Accessory

Technical Specifications

Product Instructions

Master Mode

Unit serves as Master, controllable directly or via foot controller.

Slave Mode

Unit serves as Slave, functions disabled, controlled by Master unit.

DMX Mode

Controlled by DMX controller; patterns/scenes/dimmer pack.

Stand By

Activate Stand By to kill all output momentarily.

Full On

Press Pattern and Stand By buttons to activate full intensity output.

DMX Control & Selection