14
Use the buttons to display the temperatures of
previous days.
Press the Set button to display the recorded
temperature of that period; to return to the list of stored
values press the button .
Press the button for a few seconds to exit the History
function. At least 24 hours must pass after installation of the
appliance before the first temperature can be recorded.
Keeping the button pressed for a few seconds resets
the previous recordings.
EE..33 SSiiggnnaalllliinngg iiccoonnss
The digital thermostat has the following signalling ICONS:
lit up This icon indicates compressor
activation.
lit up This icon indicates the manual defrost
function in progress.
lit up This icon indicates activation of com-
partment fans (if present).
lit up This icon indicates activation of auxiliary
users (if present).
lit up This icon indicates that a service alarm
has occurred during appliance operation.
lit up This icon indicates that the History
function is ON.
EE..44 AAllaarrmmss
• CCoommppaarrttmmeenntt hhiigghh tteemmppeerraattuurree aallaarrmm
This icon lights up and an audible alarm sounds when the
compartment temperature exceeds the set maximum value.
The alarm ceases when the temperature returns to the Set
Point. A timer, which counts the alarm duration time until it is
silenced, is also activated. Pressing the History button
displays the code HI and then in sequence, pressing the
button the number of hours since the alarm occurred.
To deactivate the icon, briefly press on it.
• CCoommppaarrttmmeenntt llooww tteemmppeerraattuurree aallaarrmm
This icon lights up and an audible alarm is activated when
the compartment temperature exceeds the set minimum
value. The alarm ceases when the temperature returns to
the Set Point. A timer, which counts the alarm duration time
until it is silenced, is also activated. Pressing the History
button displays the code LO and then in sequence, pressing
the button , the number of days since the alarm
occurred. To deactivate the icon, briefly press on it.
• SSeerrvviiccee AAllaarrmm
The message is signalled by lighting up of the icon.
Signalling also occurs with the respective code appearing
on the display and the activation of an audible alarm.
SSYYMMBBOOLLSS MMEEAANNIINNGG
WWHHAATT TTOO
DDOO
E0
rE
Compartment sensor fault
call the
service
centre
E1 Evaporator sensor fault
EE..44..11 AAllaarrmmss ssiilleenncciinngg
Alarms can be silenced:
• or by pressing on the reset alarm button
• or by pressing on the lit icon
Depending on the model.
The value indicated on the display is also automatically reset.
EE..55 PPrroodduucctt llooaaddiinngg
Distribute the product evenly inside the compartment (away
from the door and back) in order to allow good air circulation.
Cover or wrap food before placing it in the refrigerator and
avoid putting very hot foods or steaming liquids inside.
Do not leave the door open any longer than necessary when
loading or removing food.
It is advisable to keep the keys (for models with lock) in a place
only accessible to authorised personnel.
To prevent unauthorised personnel from using the appliance, it
is advisable to always close it with the key.
FF MMAACCHHIINNEE CCLLEEAANNIINNGG AANNDD MMAAIINNTTEENNAANNCCEE
WWAARRNNIINNGG
Refer to “
Warning and Safety
Information
“.
FF..11 OOrrddiinnaarryy mmaaiinntteennaannccee
FF..11..11 PPrreeccaauuttiioonnss ffoorr mmaaiinntteennaannccee
Routine maintenance operations can be carried out by non-
specialised personnel, carefully following the instructions
given below.
CCAAUUTTIIOONN
The manufacturer declines any liability for
operations carried out on the machine
without following these instructions.
FF..11..22 CClleeaanniinngg tthhee ccaabbiinneett aanndd aacccceessssoorriieess
Before using the appliance, clean all the internal parts and
accessories with lukewarm water and neutral soap, or
products that are over 90% biodegradable (in order to reduce
the emission of pollutants into the environment), then rinse and
dry thoroughly, where possible clean with dishwashing
machine. Do not use solvent-based detergents (e.g. trichloro-
ethylene) or abrasive powders for cleaning.
It is advisable to go over the external stainless steel surfaces
with a rag moistened with paraffin oil in order to create a
protective film.
Check the power cable regularly and replace it in case of signs
of wear.Have the appliance checked periodically (at least once
a year).
To Next Page
Loading...
