What to do if my Electrolux Washer displays a “HOSE” alarm due to incorrect wash and rinse temperatures?
If your Electrolux Washer displays a “HOSE” alarm due to incorrect wash and rinse temperatures, it means the hot and cold water hoses are connected to the wrong supply faucets. Connect the hot water hose to the hot water faucet and the cold water hose to the cold water faucet.
What to do if there's residue stain buildup in the dispenser drawer of my Electrolux ELFW7537AW Washer?
To address residue stain buildup in the dispenser drawer or if the detergent pack isn't dissolving in your Electrolux Washer, remove the dispenser and its inserts. Clean them using a mixture of ¾ cup of liquid chlorine bleach and one gallon of hot water. Rinse thoroughly and repeat if needed. Be sure to wear rubber or latex gloves and protect your floor and clothing from bleach.
How to clean residue stain buildup in the dispenser drawer of my Electrolux Washer?
Residue stain buildup in the dispenser drawer or detergent pack not dissolving in your Electrolux Washer, can be caused by: * Moisture in the washer. * Use of non-HE detergent. Remove and clean the dispenser and inserts with a combination of ¾ cup liquid chlorine bleach and one gallon of hot water. Rinse well, and repeat if necessary. Use only HE (high efficiency detergent) along with the recommended dosage.
What to do if my Electrolux Washer has water leaks?
If your Electrolux washer is leaking water, check the following: * Ensure the fill hose connection is tight at both the faucet and the washer. * Make sure the dispenser drawer is completely closed. * Inspect the water hoses for any damage, cuts, or corrosion. Replace them if necessary. Check and tighten hose connections, close the dispenser drawer completely, and replace damaged hoses.
What to do if my Electrolux Washer isn't draining properly?
If water in your Electrolux Washer does not drain or drains slowly: * Check if the drain hose is kinked or clogged; clean and straighten it. * Ensure the drain hose standpipe is not too tall; reduce its height to less than 8’ (2.4 m).
Why is my Electrolux ELFW7537AW leaking water?
If your Electrolux Washer is leaking, it could be due to a few reasons: * The fill hose connection might be loose at the faucet or washer. Check and tighten the hose connections, and install the provided rubber sealing washers. * The dispenser drawer may not be completely closed; ensure it is. * The water hoses may be damaged, cut, or corroded; if so, replace them.
How to fix Electrolux ELFW7537AW when water doesn't drain or drains slowly?
If the water in your Electrolux Washer doesn't drain or drains slowly, check the following: * Ensure the drain hose is not kinked or clogged; clean and straighten it. * Verify the drain hose standpipe is not too tall; it should be a maximum of 8’ (2.4 m). Reduce the height if necessary. * Check for clogged house drain pipes; unclog them or contact a plumber if needed.
Why won't my Electrolux ELFW7537AW Washer spin?
If your Electrolux Washer won’t spin, it might be because the load is too small. Add 1 or 2 similar items to help balance the load.
Why is water entering my Electrolux ELFW7537AW, but the tub does not fill?
If water is entering your Electrolux Washer but the tub isn't filling, it could be that the drain hose standpipe is too low. The standpipe must be a minimum of 23.6” (60 cm) high to prevent siphoning. Increase the standpipe height to at least 23.6” (60 cm).
Why my Electrolux ELFW7537AW Washer does not start?
If your Electrolux Washer isn't starting, ensure the power cord is securely plugged into the wall outlet. Check your house fuse or circuit breaker, and reset if necessary, but do not increase the fuse capacity. If there's a power outage, contact your local electric company. Press the start/pause button with your bare fingertip. Make sure the water supply faucets are turned on and the door is fully closed. If the motor overheats, it will automatically restart after a cool-down period of up to 30 minutes, provided the washer hasn't been manually turned off. Finally, if the light next to the start/pause button is flashing, the unit is paused.
General| Style | front load |
|---|---|
| Color | white; yes |
| Washer Capacity | 4.5 cu. ft. |
| Max Spin Speed | 1, 300 rpm |
| Number of Cycles | 10 |
| Temperature Settings | 5 |
| Internal Heater | yes |
| Control Panel | digital and knobs |
| Delay Start / End | yes; 1-12 hours |
| Child Lock | yes |
| Interior Light | yes |
| Steam | yes |
| Add Wash | no |
| Soak Settings | no |
| Remote Control | no |
| Wi-Fi | no |
| Annual Energy Consumption | 85 kwh |
| Annual Water Consumption | 4, 248 gallons |
| Voltage | 120 volts |
| Current | 15 |
Weight and Dimensions| Depth | 32 inch |
|---|---|
| Height | 38 inch |
| Width | 27 inch |
| Net Weight | 217 lbs |
Safety terms (Danger, Warning, Caution, Important) and general safety advice.
Protect children and safely dispose of old appliances.
Warnings on mixing chemicals and preventing injury during operation.
Prevent shock and injury, including grounding requirements.
Checklist for shipping hardware, leveling, water, drain, door, electrical, and tools.
Specific requirements for proper grounding and water supply connections.
Recommended clearances for alcoves, recesses, closets, and installation areas.
Circuit, power supply, and outlet requirements for safe installation.
Specifications for drain hose, standpipe diameter, and height.
Steps for unpacking, including safety precautions and handling instructions.
Instructions and diagrams for removing shipping bolts, spacers, and hardware.
Steps and tips for properly leveling the washer for stability and performance.
Procedure for ensuring the drain hose is correctly connected and secured.
Instructions for connecting hot and cold water hoses, including checks and tightening.
Final steps: plugging in, checking operation, and storing instructions.
Table detailing temperature, soil, spin, and option settings for 300 series cycles.
Table detailing temperature, soil, spin, and option settings for 400 series cycles.
Table detailing temperature, soil, spin, and option settings for 500 series cycles.
Troubleshooting common issues related to soil, stain removal, and lint.
Diagnosing and resolving issues related to unusual noises and vibration.
Resolving issues where the washer does not start, or water does not enter or drains slowly.
Addressing problems with water temperature, leaks, oversudsing, and incorrect connections.
To Next Page