What causes water in Electrolux ELFW7537AW to not drain or drain slowly?
If you are experiencing water in the washer that does not drain or drains slowly, check the drain hose of your Electrolux Washer for kinks or clogs and correct as needed. Ensure the drain hose standpipe is not too tall; the maximum height is 8’ (2.4 m). If the house drain pipes are clogged, unclog them or contact a plumber if necessary.
What causes water leaks from Electrolux ELFW7537AW?
If your Electrolux Washer is leaking water, check the fill hose connections at both the faucet and the washer to ensure they are tight. Install the rubber sealing washers provided. Make sure the dispenser drawer is completely closed. Inspect the water hoses for any damage, cuts, or corrosion, and replace them if necessary.
How to clean residue stain buildup in the gasket of my Electrolux ELFW7537AW Washer?
Residue stain buildup in the gasket of your Electrolux Washer can be caused by: * Moisture in the washer. * Use of non-HE detergent. * Overdosing detergent. * Overloading the wash drum. Perform a clean washer cycle. Scrub the gasket with Comet™ Spray Gel Mildew Stain Remover, using a brush to remove stains. Use only HE (high efficiency detergent) along with the recommended dosage. Remove the wash load immediately upon cycle completion.
Why won't my Electrolux ELFW7537AW Washer start?
Your Electrolux Washer might not start due to several reasons: * The power cord may not be properly plugged in. * A fuse may be blown, the circuit breaker tripped, or there may be a power outage. * The start/pause button may not be recognized if pressed incorrectly. * The water supply faucets may not be turned on. * The motor might be overheated (it will restart after cooling down). * The door may not be completely closed. To resolve this, ensure the plug is tightly fitted in the outlet, reset the circuit breaker or replace the fuse, press the start/pause button with a bare fingertip, turn on the water supply faucets, allow the motor to cool down, and ensure the door is closed.
What to do if wash load is too wet after spin in my Electrolux ELFW7537AW Washer?
If your wash load is too wet after the spin cycle in your Electrolux Washer, consider these solutions: * Avoid overloading the washer. * Add one or two similar items to help balance the load if it's too small. * Rearrange the load to allow for proper spinning. * Ensure the drain hose is not kinked; straighten it if necessary.
Why is my Electrolux ELFW7537AW oversudsing?
If your Electrolux Washer is oversudsing, it's likely due to: * Not using HE (high-efficiency) detergent. Run a rinse cycle and switch to a low-sudsing, high-efficiency detergent. * Using too much detergent. Run a rinse cycle and use less detergent in future loads.
Why is my Electrolux ELFW7537AW Washer making a vibrating noise?
If your Electrolux Washer is making a vibrating noise, here are a few possible causes and solutions: * Ensure the washer is resting firmly on the floor. Adjust the leveling legs if necessary. * Confirm that the shipping bolts and foam block have been removed during installation. * The wash load may be unevenly distributed in the drum. Stop the washer and rearrange the load.
How to remove residue left in drum of Electrolux ELFW7537AW?
To remove residue left in the drum of your Electrolux Washer, wipe the drum with a nonabrasive household cleanser, then rinse. Also, shake or brush excess dirt and sand from items before washing.
What to do if wash load is too wet after spin in Electrolux ELFW7537AW Washer?
If your Electrolux Washer leaves the wash load too wet after spinning, avoid overloading the washer. If the load is too small, add one or two similar items to help balance it. Ensure the load is arranged properly for spinning. Straighten the drain hose to ensure proper drainage.
How to clean residue stain buildup in gasket of Electrolux ELFW7537AW Washer?
If you find residue stain buildup in the gasket of your Electrolux Washer, it could be due to moisture, using non-HE detergent, overdosing detergent, overloading the wash drum, leaving a wet load in the washer, or using cold water washes that don't fully dissolve detergents. To resolve this, perform a clean washer cycle. Scrub the gasket with Comet™ Spray Gel Mildew Stain Remover, using a brush to remove stains. Use only HE (high efficiency) detergent at the recommended dosage and remove the wash load immediately after the cycle is complete.
General| Style | front load |
|---|---|
| Color | white; yes |
| Washer Capacity | 4.5 cu. ft. |
| Max Spin Speed | 1, 300 rpm |
| Number of Cycles | 10 |
| Temperature Settings | 5 |
| Internal Heater | yes |
| Control Panel | digital and knobs |
| Delay Start / End | yes; 1-12 hours |
| Child Lock | yes |
| Interior Light | yes |
| Steam | yes |
| Add Wash | no |
| Soak Settings | no |
| Remote Control | no |
| Wi-Fi | no |
| Annual Energy Consumption | 85 kwh |
| Annual Water Consumption | 4, 248 gallons |
| Voltage | 120 volts |
| Current | 15 |
Weight and Dimensions| Depth | 32 inch |
|---|---|
| Height | 38 inch |
| Width | 27 inch |
| Net Weight | 217 lbs |
Safety terms (Danger, Warning, Caution, Important) and general safety advice.
Protect children and safely dispose of old appliances.
Warnings on mixing chemicals and preventing injury during operation.
Prevent shock and injury, including grounding requirements.
Checklist for shipping hardware, leveling, water, drain, door, electrical, and tools.
Specific requirements for proper grounding and water supply connections.
Recommended clearances for alcoves, recesses, closets, and installation areas.
Circuit, power supply, and outlet requirements for safe installation.
Specifications for drain hose, standpipe diameter, and height.
Steps for unpacking, including safety precautions and handling instructions.
Instructions and diagrams for removing shipping bolts, spacers, and hardware.
Steps and tips for properly leveling the washer for stability and performance.
Procedure for ensuring the drain hose is correctly connected and secured.
Instructions for connecting hot and cold water hoses, including checks and tightening.
Final steps: plugging in, checking operation, and storing instructions.
Table detailing temperature, soil, spin, and option settings for 300 series cycles.
Table detailing temperature, soil, spin, and option settings for 400 series cycles.
Table detailing temperature, soil, spin, and option settings for 500 series cycles.
Troubleshooting common issues related to soil, stain removal, and lint.
Diagnosing and resolving issues related to unusual noises and vibration.
Resolving issues where the washer does not start, or water does not enter or drains slowly.
Addressing problems with water temperature, leaks, oversudsing, and incorrect connections.
To Next Page