11
Residual risk Description of hazardous
situation
Crushing or injury The specialised personnel may
not correctly fix the control panel
when accessing the technical
compartment. The panel could
close suddenly.
Crushing or shearing Possible risk of injury to upper
limbs during the hood closing
operation.
Residual risk Description of hazardous
situation
Tipping of loads When handling the machine or the
packing containing it, using unsuit-
able lifting systems or accessories
or with the unbalanced load
Chemical Contact with chemical substances
(e.g. detergent, rinse aid, scale
remover, etc.) without taking
adequate safety precautions.
Therefore always refer to the
safety cards and labels on the
products used.
IMPORTANT
In case of a significant anomaly (e.g. short circuits,
wires coming out of the terminal block, motor
breakdowns, worn electrical cable sheathing, etc.)
the operator must immediately deactivate the
machine.
E GENERAL INFORMATION
E.1 Introduction
Given below is some information regarding the intended use of
this appliance, its testing, and a description of the symbols
used (that identifies the type of warning), the definitions of
terms used in the manual and useful information for the
appliance user.
E.2 Definitions
Listed below are the definitions of the main terms used in the
manual. It is advisable to read them carefully before use.
Operator machine installation, adjustment, use,
maintenance, cleaning, repair and trans-
port personnel.
Manufacturer Electrolux Professional SpA or any other
service centre authorised by Electrolux
Professional SpA.
Operator for
normal
machine use
an operator who has been informed and
trained regarding the tasks and hazards
involved in normal machine use.
Customer
Care service
or specialised
technician
an operator instructed/trained by the
Manufacturer and who, based on his
professional and specific training, experi-
ence and knowledge of the accident-
prevention regulations, is able to appraise
the operations to be carried out on the
machine and recognise and prevent any
risks. His professionalism covers the
mechanical, electrotechnical and elec-
tronics fields.
Danger source of possible injury or harm to health.
Hazardous
situation
any situation where an operator is
exposed to one or more hazards.
Risk a combination of probabilities and risks of
injury or harm to health in a hazardous
situation.
Protection
devices
safety measures consisting of the use of
specific technical means (guards and
safety devices) for protecting operators
against risks.
Guard an element of a machine used in a specific
way to provide protection by means of a
physical barrier.
Safety device a device (other than a guard) that elimi-
nates or reduces the risk; it can be used
alone or in combination with a guard.
Customer the person who purchased the machine
and/or who manages and uses it (e. g.
company, entrepreneur, firm).
Emergency
stop device
a group of components intended for the
emergency stop function; the device is
activated with a single action and pre-
vents or reduces damage to persons/
machines/property/animals.
Electrocution an accidental discharge of electric current
on a human body.
E.3 Machine and Manufacturer’s
identification data
A reproduction of the marking or dataplate on the machine is
given below:
The dataplate gives the product identification and technical data;
listed below is the meaning of the various information given on it.
F.Mod. factory description of product
Comm.Model commercial description
PNC production number code
Ser.No. serial number
400V 3N~ power supply voltage
230V 3~ - 230V 1N~ electric convertibility (depending
on the model)
Hz power supply frequency
Max – kW
max. power
Nominal – kW nominal power
IPX4 dust and water protection rating
CE CE marking
Electrolux Professio-
nal SpA Viale Treviso
15 33170 Pordenone
Italy
manufacturer
2017
F.Mod.
Comm. Model:
PNC Ser.Nr.
EL Hz Max 12.9 kW
Nominal 9.9 kW
6.9 kW
Min
Electrolux Professional spa - Viale Treviso, 15 - 33170 Pordenone (Italy)
IP
Type ref.
To Next Page
Loading...
