elero TempoTel 2 User Manual (English)

Questions and Answers:

J
Jeff MorganAug 22, 2025
What to do if my elero TempoTel 2 drive does not run but the status display lights red, flashes orange, or lights green (unidirectional)?
- S
  Shelly RomeroAug 22, 2025
  If the elero Transmitter drive isn't running and the status display shows red, flashes orange, or lights green (if unidirectional), it could be due to several reasons. The receiver might be too far away; try reducing the distance. The receiver could also be defective, in which case you should switch it on or exchange it. Alternatively, the receiver might not be programmed yet; try programming the receiver.
J
jamesrodriguezSep 1, 2025
How to fix inaccurate end positions on my elero TempoTel 2?
- H
  Heather BrownSep 2, 2025
  If the end positions are approached inaccurately, have the end positions set by a specialist in accordance with the product instructions.
T
Thomas JamesAug 31, 2025
What to do if the required drive does not run with my elero TempoTel 2?
- E
  Ernest HughesAug 31, 2025
  If the required drive isn't running with your elero Transmitter, it might be due to an incorrect group or channel selection. Ensure you select the correct group or channel.
D
desiree74Aug 30, 2025
What to do if my elero TempoTel 2 Transmitter drive operates in the wrong direction?
- M
  Molly WheelerAug 30, 2025
  If your elero Transmitter drive is operating in the wrong direction, it's likely that the directions are incorrectly allocated. To fix this, delete the transmitter and reprogram it.
S
Shaun BlackwellAug 28, 2025
What to do if there is no timed switching function for automatic switching commands after replacing the batteries in my elero TempoTel 2?
- J
  Julia McleanAug 29, 2025
  If the timed switching function for automatic switching commands is absent after a battery replacement in your elero Transmitter, it's likely that the power supply was interrupted for too long. To resolve this, set the date and time.
T
Teresa HansonAug 27, 2025
What to do if the elero TempoTel 2 hand-held transmitter does not carry out the set switching commands accurately?
- K
  Katelyn BishopAug 27, 2025
  If the elero Transmitter hand-held transmitter isn't executing the set switching commands accurately, the holiday function might be switched on. Try switching the holiday function off.
D
Dana StoneAug 26, 2025
Why does the elero TempoTel 2 Transmitter Astro program switch inaccurately?
- M
  michelle49Aug 27, 2025
  If the Astro program on your elero Transmitter is switching inaccurately, the date might be set incorrectly; ensure the correct date is set. Also, check if the holiday function is activated and switch it off if necessary. Finally, the Astro offset might be set, so adjust the Astro offset.
K
Kevin ChenAug 25, 2025
What to do if my elero TempoTel 2 Transmitter drive does not run and the status display does not light?
- S
  Shelby WoodardAug 26, 2025
  If the elero Transmitter drive isn't running and the status display remains unlit, the batteries are likely the issue. Either the batteries are low, in which case you should insert new batteries, or the batteries are incorrectly installed, so ensure they are correctly inserted.
J
Jessica BrandtAug 23, 2025
Why does my elero TempoTel 2 not carry out the set switching commands?
- J
  jriggsAug 23, 2025
  If your elero Transmitter isn't executing the set switching commands, check if the date and time are set correctly. Another reason could be that the operating mode is set to “MANUAL”; switch it to “AUTO”. Also, ensure that the timed switching function is activated for the specific channel.

elero TempoTel 2 Specifications

General

Frequency	868.3 MHz
Power source	Battery
Battery type	CR2032
Operating temperature	-20°C to +60°C
Transmission range	200 m (open field)
Battery life	2 years (typical)