elero TempoTel 2 - User Manual

Questions and Answers

S
sherry88Sep 23, 2025
What to do if elero Transmitter drive does not run but status display lights up?
- A
  Alyssa YoungSep 23, 2025
  If your elero Transmitter drive isn't running but the status display lights up red or flashes orange (Unidirectional: Status display lights green), it could be due to a few reasons: * The receiver is outside radio range. Try reducing the distance to the receiver. * The receiver isn't operating or is faulty. Try switching on or replacing the receiver. * The receiver hasn't been programmed yet. Program the receiver.
J
Jessica BrandtAug 23, 2025
Why does my elero TempoTel 2 not carry out the set switching commands?
- J
  jriggsAug 23, 2025
  If your elero Transmitter isn't executing the set switching commands, check if the date and time are set correctly. Another reason could be that the operating mode is set to “MANUAL”; switch it to “AUTO”. Also, ensure that the timed switching function is activated for the specific channel.
K
Kevin ChenAug 25, 2025
What to do if my elero TempoTel 2 Transmitter drive does not run and the status display does not light?
- S
  Shelby WoodardAug 26, 2025
  If the elero Transmitter drive isn't running and the status display remains unlit, the batteries are likely the issue. Either the batteries are low, in which case you should insert new batteries, or the batteries are incorrectly installed, so ensure they are correctly inserted.
D
Dana StoneAug 26, 2025
Why does the elero TempoTel 2 Transmitter Astro program switch inaccurately?
- M
  michelle49Aug 27, 2025
  If the Astro program on your elero Transmitter is switching inaccurately, the date might be set incorrectly; ensure the correct date is set. Also, check if the holiday function is activated and switch it off if necessary. Finally, the Astro offset might be set, so adjust the Astro offset.
T
Teresa HansonAug 27, 2025
What to do if the elero TempoTel 2 hand-held transmitter does not carry out the set switching commands accurately?
- K
  Katelyn BishopAug 27, 2025
  If the elero Transmitter hand-held transmitter isn't executing the set switching commands accurately, the holiday function might be switched on. Try switching the holiday function off.
E
Ellen SmithSep 16, 2025
Why does my elero Transmitter drive operate in the wrong direction?
- L
  Laurie BallSep 16, 2025
  If your elero Transmitter drive operates in the wrong direction, it's because the directions are incorrectly allocated. To fix this, delete the transmitter and reprogram it.
S
Stacy HawkinsSep 13, 2025
Why is there no timed switching function for automatic switching commands on my elero TempoTel 2 after replacing the batteries?
- Q
  qjordanSep 13, 2025
  If there is no timed switching function for automatic switching commands after replacing the batteries, the power supply was likely interrupted for too long. To fix this, set the date and time.
J
jacobsveronicaSep 14, 2025
How to fix elero Transmitter when drive does not run and status display does not light up?
- S
  sarah63Sep 15, 2025
  If your elero Transmitter drive isn't running and the status display doesn't light up, it's likely due to exhausted or incorrectly installed batteries. Try inserting new batteries or ensuring the batteries are correctly installed.
J
Jordan RiggsSep 5, 2025
Why does my elero Power Supply drive operate in the wrong direction?
- V
  vnicholsSep 5, 2025
  If your elero Power Supply drive operates in the wrong direction, it means the directions are incorrectly allocated. To fix this, delete the transmitter and reprogram it.
A
aleeSep 3, 2025
What to do if elero Power Supply drive does not run but the status display lights up?
- C
  christine04Sep 3, 2025
  If your elero Power Supply drive isn't running but the status display lights up red or flashes orange (or lights up green for unidirectional models), it could be due to several factors: * The receiver might be too far away. Try reducing the distance to the receiver. * The receiver could be faulty. Try switching it on or exchanging it. * The receiver may not be programmed yet. Program the receiver.

Summary

Safety instructions

Safety instructions for radio operation

Technical data

Mounting of wall bracket

Device explanation

Explanation of functions

Initial operation

Details the first steps to switch on and operate the transmitter.

Factory settings

Menu structure

Menu mode

DATE;TIME menu

PROGRAM menu

Astro evening

Controls up movement by time and down by Astro function.

ADMINISTRATION menu

SETTINGS Menu

Global settings

Astro

Adapts Astro switching times using town data or coordinates.

Town selection

Longitude; latitude

Astro offset

Settings for specific channels

Product selection

Assigns product-specific functions and maximum running times to channels.

Program position ↓ (DOWN)

Program position ↑ (UP)

FUNCTION menu

Factory setting

Resets all settings to factory defaults, requiring re-initialization.

Programming the transmitter

Programming additional transmitters

Synchronous Programming Mode

Stopping programming mode (bidirectional) in the transmitter

Approaching end positions roller shutter;awning; venetian blind

Programming the intermediate position in the receiver

Programming the ventilation;tilting position in the receiver

Approaching intermediate position

Approaching ventilation;tilting position

Deleting positions;deleting transmitters

Deleting the intermediate position in the receiver

Deleting the ventilation;tilting position in the receiver

Deleting the transmitter channel in the receiver

Removes a transmitter channel from the receiver and the transmitter.

Deleting all the transmitters in the receiver

Deletes all programmed transmitters from the receiver.

Expert Settings

Battery replacement

Troubleshooting

Repair

elero TempoTel 2 Specifications

General

Frequency	868.3 MHz
Power source	Battery
Battery type	CR2032
Operating temperature	-20°C to +60°C
Transmission range	200 m (open field)
Battery life	2 years (typical)

Related product manuals