Eliminator Lighting MEGA FLAT HEX PAK - Advanced System Menu Settings; RGBWA+UV Dimmer and Strobe

13
SYSTEM MENU
RGBWA + UV Dimmer Mode:
1. Plug the xture in and press the MODE button until “r.XXX” is displayed. This indicates that the
xture is in Red dimming mode.
2. Press the UP and DOWN buttons to adjust intensity. After you have nished adjusting the intensity,
or if you would like to skip to the next color, press the SET UP button.
3. When “G.XXX” is displayed, the xture is in Green dimming mode. Press the UP and DOWN buttons
to adjust intensity.
4. When “b.XXX” is displayed, the xture is in Blue dimming mode. Press the UP and DOWN buttons
to adjust intensity.
5. When “U.XXX” is displayed, the xture is in White dimming mode. Press the UP and DOWN buttons
to adjust intensity.
6. When “A.XXX” is displayed, the xture is in Amber dimming mode. Press the UP and DOWN buttons
to adjust intensity.
7. When “u.XXX” is displayed, the xture is in UV dimming mode. Press the UP and DOWN buttons
to adjust intensity.
8. After you have adjusted the colors as desired, you can then activate strobing by pressing the SET
UP button to enter the strobe mode.
9. “FS.XX” will be displayed, indicating that the xture is in strobe mode. The strobe can be adjusted
between “00” (ash off) to “15” (fastest ash).
Auto Run Mode: There are 3 types of Auto Run Modes to choose from: Color Fade, Color Change, and
both modes running together. The running speed is adjustable in all 3 modes.
1. Plug the xture in and press the MODE button until either “AFXX”, “AJXX”, or “A-JF” is displayed.
Press the SET UP Button to change between the 3 Auto Run modes.
• AFXX = Color Fade mode, with 16 programs to choose from.
• AJXX = Color Change mode, with 16 programs to choose from.
• A-JF = Both Color Fade and Color Change modes running.
2. After selecting your desired mode, use the UP and DOWN buttons to scroll through the available
programs. Note that this step is not applicable when running both modes together (option A-JF).
3. 2. Press the SET UP button until “SP.XX” is displayed. Now adjust the running speed of your desired
program. Use the UP or DOWN button to adust the speed between “SP.01” (slowest) and “SP.16”
(fastest). Press the SET UP button to return to your desired Auto Run Mode.
ADJ Remote Activation: This function is used to activate or deactivate the IR sensor. When this
function is activated, the xture can be controlled using the ADJ UC IR. Please see the IR Remote
Control section of this manual for detailed information.
1. Plug the xture in and press the MODE button until “dXX” is displayed. “XX” represents either “on”
or “oF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate (“Iron”) or deactive (“IroF”) the remote function.
DMX State: This mode denes how the xture will behave in the event that the DMX signal is lost or
interrupted, or the mode it will default to when power is rst connected.
1. Plug the xture in and press the MODE button until “d.XXX” is displayed. “XXX” represents the
currently selected DMX address.
2. Press the SET UP button so that “nodn” is displayed. Use the UP and DOWN buttons to scroll
through the DMX states.
• “bLAC” (Blackout) - The unit will automatically go into stand by mode.
• “LASt” (Last State) - The unit will stay in the last DMX set up.
• “ProG” (Auto Run) - The unit will automatically go into Auto Run mode.
• “nAnU” - The unit will automatically go into RGBA+UV dimmer mode.
3. Use the UP and DOWN buttons to nd the desired DMX state, then press SET UP to conrm and exit.