Elkay LZWSM8 1A Series User Manual

Page 1 98557C (Rev. J - 8/14)
EZWSMD*1A EZWSM8*1A EZWSM8*2A LZWSMD*1A LZWSM8*1A LZWSM8*2A
Installation/Care/Use Manual
EZH20 In Wall Bottle Filling Station
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLER BE PROTECTED BY A GROUND
FAULT CIRCUIT INTERRUPTER (GFCI)
FIG. 2FIG. 1
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
LZWSM8* LZWSMD* LZWSM8P* LZWSMDP*
EZWSM8* EZWSMD* EZWSM8P* EZWSMDP*

Elkay LZWSM8 1A Series Specifications

General

Model	LZWSM8
Number of Stations	1
Number of Openings	1
Bubbler Activation	Push Button
Water Source	Plumbed
Material	Stainless Steel
Cooling Method	Refrigerated
Filtration	Yes
Cooling	Yes
Heating	No
Voltage	115V
Hertz	60Hz
Refrigerant Type	R-134A
Type	Bottle Filling Station
Mounting Style	Wall Mount
Installation	Wall
Bottle Filling Station Activation	Sensor Activated

Summary

Installer Information

Important Safety Notes

Critical safety warnings and installer recommendations for proper installation.

Quick Connect Fittings Operation

Guide to using the quick connect fittings for water supply connections.

Rough-In Dimensions LZWSM8*/LZWSMD*

Rough-In Dimensions LZWSM8P*/LZWSMDP*

Installation Instructions

Filter and Water Supply Setup

Steps for installing the filter and connecting water supply lines.

Final Assembly and Plumbing

Mounting panels, connecting water lines, and drain setup.

Installation Completion and Testing

Unit Securing and Dispensing Test

Steps for securing panels, testing dispensing, and checking for leaks.

Control Board Settings: BF6-BF8 Programs

Software Verification and Filter Monitor

Instructions for verifying software and resetting the filter monitor.

IR Sensor Range Adjustment

Procedure for adjusting the IR sensor range for BF6-BF8 programs.

Control Board Settings: BF9 Programs

Unit Type and Filter Capacity

Guide to setting unit type and filter capacity for BF9 program.

Bottle Count Reset and IR Sensor

Procedures for resetting bottle count and setting IR sensor range.

Control Board Settings: BF11 Programs

Unit Type and Filter Size Configuration

Instructions for setting unit type and filter size for BF11 program.

Bottle Count Reset for BF11

Procedure to reset the bottle count for BF11 program.

BF11 Program: Filter Capacity Setting

Parts and Service Information

Water Sentinel Filter Parts List

Exploded view and part numbers for the water filter system.

Replacement Part Kits and Contact

List of available replacement part kits and service contact details.