Elma Elmasonic S User Manual (English)

Other manuals for Elma Elmasonic S

Verification Of Operating Functions7 pages

Questions and Answers:

R
rebeccabellAug 14, 2025
What to do if my Elma Elmasonic S has no ultrasonic operation and LEDs are blinking?
- S
  Sydney BryantAug 14, 2025
  If your Elma Ultrasonic Jewelry Cleaner shows no ultrasonic operation and the LEDs are blinking alternately, it indicates a fault. This could be due to an adverse filling level, so try changing the filling level and switch the unit off and on. If the fault persists after switching the unit off and on, return it to the supplier or manufacturer, as it may indicate an electronics fault.
L
llynchAug 18, 2025
What to do if my Elma Elmasonic S Ultrasonic Jewelry Cleaner has no heating function and LEDs are blinking?
- J
  judith37Aug 18, 2025
  If your Elma Ultrasonic Jewelry Cleaner shows no heating function and the LEDs of the LED temperature blink alternately, indicating a fault, switch the unit off and on. If the fault persists, return the unit to the supplier or manufacturer, as it likely indicates an electronics fault.
C
clarkalyssaAug 21, 2025
Why is my Elma Elmasonic S Ultrasonic Jewelry Cleaner not cleaning well?
- R
  Richard Walters DDSAug 21, 2025
  If you're getting unsatisfactory cleaning results from your Elma Ultrasonic Jewelry Cleaner, it could be due to a few reasons. You might not be using a suitable cleaning medium, so ensure you're using the right one. The cleaning temperature might not be high enough, so try heating up the cleaning liquid. Also, the cleaning period could be too short; try repeating the cleaning interval.
H
Holly MillerAug 25, 2025
What to do if my Elma Elmasonic S unit does not heat up and the LED temperature is dark?
- D
  David JonesAug 25, 2025
  If your Elma Ultrasonic Jewelry Cleaner isn't heating up and the LED temperature is dark, first ensure that the turning knob temperature is not in the '0' position; switch it on. Also, check that the unit is switched on using the key on/off. If the problem persists, there may be an electronics fault, and you should return the unit to the supplier or manufacturer.
A
Amy HallAug 27, 2025
Why does my Elma Elmasonic S have an unsatisfactory heating-up period?
- C
  Catherine HansonAug 27, 2025
  An unsatisfactory heating-up period in your Elma Ultrasonic Jewelry Cleaner can be due to loss of heating energy; try using a cover (optional accessory equipment). It could also be caused by no mixing of cleaning liquid; for example, switch on ultrasound.
B
Brenda HarmonAug 31, 2025
Why does my Elma Elmasonic S produce boiling noise during heating-up?
- R
  Richard BrooksAug 31, 2025
  If your Elma Ultrasonic Jewelry Cleaner produces a boiling noise during heating-up, this can be caused by no mixing of cleaning liquid. To resolve this, switch on the ultrasound.
A
Ashley AlvarezSep 3, 2025
What to do if the set temperature is exceeded in my Elma Elmasonic S Ultrasonic Jewelry Cleaner?
- J
  James SmithSep 3, 2025
  If the set temperature is exceeded in your Elma Ultrasonic Jewelry Cleaner, it could be because the temperature sensor isn't measuring the average temperature due to no revolution. Try mixing the liquid manually or by means of ultrasound. Alternatively, if the set temperature is too low, the ultrasonic energy might be heating up the liquid more than required; for low set temperatures, avoid switching on the heating. You can also switch on ultrasound for short periods only.
S
Susan TaylorSep 7, 2025
What to do if the mains cable is damaged on my Elma Elmasonic S?
- J
  Jennifer LarsonSep 7, 2025
  If the mains cable of your Elma Ultrasonic Jewelry Cleaner is damaged, obtain an original spare mains cable from the manufacturer or supplier.
K
Kathy GonzalezSep 10, 2025
What to do if the casing of my Elma Elmasonic S Ultrasonic Jewelry Cleaner is damaged?
- S
  Sheryl RubioSep 12, 2025
  If the casing of your Elma Ultrasonic Jewelry Cleaner is damaged, return the unit to the supplier or manufacturer.

Elma Elmasonic S Specifications

General

Model	Elmasonic S
Ultrasonic Frequency	37 kHz
Type	Ultrasonic Cleaner
Ultrasonic Power	35 W
Material	Stainless Steel
Operating Mode	Continuous or timed operation
Heating	Yes

Summary

General Information

Important Safety Warnings

Read before initial operation! Covers intended use, user, mains connection, electrical accidents, cleaning liquid, hot surfaces, noise, sound transmission.