How to fix rough cut with EMAK EF 105?
A rough cut with your EMAK Lawn Mower can be caused by a worn or blunt blade (renew or regrind the blade), an incorrect cutting height (adjust the cutting height), the engine speed being too slow (set the maximum engine speed), driving speed being too fast (reduce driving speed), or different tire pressure at the wheels (inflate to the correct air pressure specified on the tire).
Why EMAK EF 105 Lawn Mower engine does not start?
The EMAK Lawn Mower engine might fail to start due to several reasons: a lack of fuel (in this case, fill the tank, check the tank bleeding, and the fuel filter), poor or contaminated fuel (always use fresh fuel from clean containers and clean the carburettor), a contaminated air filter (clean the air filter according to the engine manufacturer's instructions), no ignition spark (clean or replace the spark plug, check the ignition cable and system), or too much fuel in the engine combustion chamber (unscrew and dry off the spark plug).
What to do if EMAK EF 105 Lawn Mower starter does not work?
If the starter of your EMAK Lawn Mower isn't working, it could be due to a flat or weakly charged starter battery (charge the starter battery), a malfunctioning safety switch on the operator’s seat (sit correctly or the switch is defective), a faulty safety switch on the brake pedal (press the brake pedal down fully), the mower mechanism being switched on (switch off the mower mechanism), a blown fuse on the (+) cable of the starter battery (check and replace the fuse if necessary), grass that is too long or wet (correct the cutting height and move back to clear the mower mechanism), or a blocked discharge channel/mower deck (clean the discharge channel/mower deck after stopping the engine and removing the ignition key).
What to do if EMAK Lawn Mower fill level display does not respond?
If the fill level display on your EMAK Lawn Mower isn't responding, it's likely due to mown grass stuck to the fill level display lever. Remove the mown grass and ensure the lever can move freely.
What does Err 01 mean on EMAK EF 105 Lawn Mower?
Err 01 on your EMAK Lawn Mower indicates that the seat switch ECU detects an invalid status of the seat switch. To resolve this, switch the ignition off, then apply and release load from the seat several times.
What does Err 02 mean on EMAK Lawn Mower?
Err 02 on your EMAK Lawn Mower means that the ECU detects an invalid status of the brake switch. To fix this, switch the ignition off and then back on to position 2.
What does Err 03 mean on EMAK EF 105?
Err 03 on your EMAK Lawn Mower indicates that the ECU detects an invalid status of the mower mechanism switch. To solve this, switch the ignition off and back on to position 2, then operate the mower mechanism switch several times.
What does Err 04 mean on EMAK EF 105 Lawn Mower?
Err 04 on your EMAK Lawn Mower signifies that the ECU detects an invalid status of the box switch. To resolve this, switch the ignition off and back on to position 2, then open and close the box several times.
What does Err 05 mean on EMAK EF 105 Lawn Mower?
Err 05 on your EMAK Lawn Mower means the ECU detects an invalid status of the transmission switch. To correct this, switch the ignition off and back on to position 2, then operate the reverse pedal several times.
What does Err 06 mean on EMAK Lawn Mower?
Err 06 on your EMAK Lawn Mower indicates that the ECU detects an invalid status of the discharge channel switch. To fix it, switch the ignition off and back on to position 2, then remove and reinstall the discharge channel.
General| Brand | EMAK |
|---|---|
| Model | EF 105 |
| Category | Lawn Mower |
| Language | English |
To Next Page
