EMAK SPL 910 T User Manual (English)

Questions and Answers:

L
Latasha RobertsAug 4, 2025
What to do if EMAK Log Splitter fails to split the log?
- O
  oandersonAug 4, 2025
  If your EMAK Log Splitter fails to split the log, it might be due to several reasons. The log may exceed the permitted dimensions; in this case, try cutting a small part or use other means to reduce its size. Another reason might be incorrect positioning of the log; try changing its position in relation to the wedge. Also, the wedge may not be sharp enough; sharpen it and check for burrs or nicks, filing if necessary. If you notice an oil leak, locate it and contact your dealer. Low hydraulic pressure can also be the cause; in this case, contact your dealer.
L
Lisa BrownAug 13, 2025
Why is my EMAK SPL 910 T leaking oil from the unions, pump, or cylinder?
- M
  Monique DavisAug 13, 2025
  If your EMAK Log Splitter is leaking oil from the unions, pump, or cylinder, it could be due to unions not being properly tightened; try tightening them. Alternatively, the seals may be worn, in which case you should contact your dealer.
T
Thomas SmithAug 23, 2025
How to fix EMAK SPL 910 T rod advancing jerkily with vibrations and foamy oil?
- S
  Sheila StevensonAug 23, 2025
  If the rod on your EMAK Log Splitter advances jerkily or with strong vibrations, and foamy oil comes out from the filler cap, it may be due to air in the circuit. Check the oil level and top up if necessary. Ensure that the pump is not sucking in air. Also, verify that the connections are not restricted or the pipes damaged in the system from the tank to the pump. If the problem persists, contact your dealer.

EMAK SPL 910 T Specifications

General

Brand	EMAK
Model	SPL 910 T
Category	Log Splitter
Language	English

Summary

Introduction

Description of the Machine

Symbols Used

Explains standard graphic symbols for safety and operation, emphasizing their importance for log splitter use.

Technical Data

Right Way to Lift the Machine

Instructions on correctly lifting the machine using a hook, specifying capacity and hitch point for safe handling.

Size of the Logs to be Split

Details maximum log dimensions and factors influencing splitting difficulty, referencing visual guides.

Serial Number Label

Identifies the serial number label's location and purpose for machine identification and reference.

Safety

General Safety Regulations

Lists essential safety rules for log splitter operation, covering user responsibilities and hazard avoidance.

Safety Protective Clothing

Recommends specific protective gear, like shoes, gloves, and eye protection, for safe log splitter operation.

Operating the Machine

For Machines with Electric Motor (SPL 910 T)

Step-by-step guide for starting and stopping electric log splitter models, including power connection.

For Machines with Premium Graded Fuel Engine (SPL 910 SC)

Instructions for starting and stopping gasoline engine log splitter models, covering engine warm-up.

For Machines Driven by Cardan Shaft (SPL 910 PTO)

Procedures for operating tractor-driven log splitter models, including PTO connection and tractor setup.

Opening the Cylinder

Details the procedure for raising the hydraulic cylinder to the working position before operating the log splitter.

Lighting

Emphasizes the necessity of adequate lighting in the work area for safe operation and maintenance.

Use

Switching On/Off of the Electric Log Splitter (SPL 910 T)

Provides detailed steps for turning electric log splitter models on and off safely.

Switching On/Off of the Log Splitter with Premium Graded Fuel Engine (SPL 910 SC)

Details for starting and stopping gasoline engine log splitter models, including choke and throttle use.

Switching On/Off of the Tractor-Driven Log Splitter (SPL 910 PTO)

Instructions for powering on and off tractor-driven log splitters, ensuring safe connection and operation.

How to Use Log Splitter

Step-by-step guide on the correct usage of the log splitter for splitting wood efficiently and safely.

Use of the Movable Table (Optional)

Instructions for utilizing the optional movable table to split shorter logs effectively.

Closing the Cylinder for Transport

Procedure for lowering and securing the hydraulic cylinder for safe transportation of the log splitter.

Manual Handling of the Log Splitter

Guidelines for safely moving the log splitter manually, focusing on balance and carrying points.

Routine Maintenance

How to Change the Hydraulic Oil

Step-by-step guide for replacing the hydraulic oil, including drainage, refill, and bleeding the system.

Recommended Oils

Lists specific types of hydraulic oils recommended for the log splitter's hydraulic cylinder.

Sharpening the Wedge

Instructions on maintaining the wedge's sharpness for optimal wood splitting performance.

Troubleshooting

Resetting of the Thermal Cut-out of the Electric Motor

Procedure for resetting the electric motor's thermal protection device after overload.

EMAK SPL 910 T User Manual

Table of Contents