Emerson ControlWave EFM 3808 - Configuring the CPU;System Controller Board

ControlWave Express Instruction Manual (CI-ControlWave Express)
Revised Mar-2011 Installation 2-7
2.3 Configuring the CPU/System Controller Board
To configure the CPU/System Controller board, you need to set some
switches and jumpers.
S1
1
2
34
12
3
45678
1
1
2
2
3
4
5
6
RJ-45
RJ-45
W3: 1-2 = Battery Enabled
2-3 = Battery Disabled
W2: 1-2 = COM2 CTS from Port
W5: 1-2 = 12/24V Power Supply
Shut-down Hysterisis
Shut-down Hysterisis
2-3 = 6V Power Supply
W6: 1-2 = 12V Power Supply
Shut-down
Shut-down
2-3 = 6/24V Power Supply
2-3 = COM2 CTS to RTS
W1: 1-2 = COM1 CTS from Port
2-3 = COM1 CTS to RTS
SW3 - COM3 Config.
RS-485 Receiver Biasing & Termination
2-Wire, 4-Wire Selction
J5 - COM3
Piggy-back
Radio Intf.
J3 - I/OBUS
Intf. to
CPU Board
P1
WE
J7
MSP430
JTAG
Header
J9
PLD JTAG
Header
J8
Emulation
Header
J3
J5
W14
W16
W7
W1
3 2 1
W18
F3
W2
W3
W8
W6
W5
W15
W12
W13
Pulse
Input
LCD/
Keypad
Power
Power
GND
Sec. Battery Input
Power In +
Aux. Power Out +
Solar Pwr. In +
GND
GND
GND
1
5
6
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
1
2
3
4
5
TXD-/TXD
GND
RXD+
RXD-/RXD
Input
Input
Output
Output
TXD+
4
1
2
3
GND
PULSE 1
PULSE 2
Input
Input
Output
PULSE
PWR
COM2
RS-232
10/100
Base-T
Ethernet
Port
COM1
RS-232
COM1
RS-232
Configuration
Options
Switch
Recovery
Mode &
COM./Status
LEDs
1
O N
2
3
4
O N
12
3
4
5
6
7
8
Receive
LED
Transmit
LED
TXD
GND
DCD
RXD
DTR
DSR
RTS
CTS
TXD
T
X
D
GND
G
N
D
DCD
RXD
R
X
D
Input
Input
Output
Output
Output
Input
Input
Input
Input
Output
Output
Output
Input
Input
DTR
DSR
RTS
CTS
RTD
Input
1
2
3
RTD-
CAUTION:
Damage WILL occur to
the CPU if the Ethernet
network is connected
to connector J2!
RTD EXC
RTD+
COM3
RS-232
RS-485
PG
WD
STA6
STA5
STA4
STA3
STA2
STA1
TX1
RX1
TX3
RX3
TX2
RX2
IDLE
W12 - W16: 1-2 = COM3 RS-232
2-3 = COM3 RS-485
W7: 1-2 = 12/24V Power Fail
Trip Point Hysterisis
Trip Point Hysterisis
2-3 = 6V Power Fail
W8: 1-2 = 12V Power Fail
Trip Point
Trip Point
2-3 = 6/24V Power Fail
Trip Point
NOTE:
J7, J8, J9
Factory Use
W17
RJ-45
Solar Pwr. In and Aux. Power Out
are not available on units equipped
with an Ethernet Port.
Ultra Low Power & Low Power
CPU/System Controller Bds.
Don’t have an Ethernet Port.
NOTE:
Do Not Connect a 24V Solar Panel
to Connector TB1-1 & TB1-2!
Note: W17 is N/A on 24V Systems
Do Not Connect a 24V Solar
Panel to TB1-1 & TB1-2!
W17: 6/12V CPUs
1-2 = 6V S. P. Charging System
2-3 = 12V S. P. Charging System
W17: 12/24V CPUs
W18: COM1 connector
selection
1 to 2 = J4 active
2 to 3 = J11 active
1-2 = 12V S. P. Charging System
2-3 = N/A
NOTE:
J11 normally used
for CW GFC and CW
Express PAC only.
2 = Watchdog
1 = Idle
}
CR1
CR1
2
1
Figure 2-3. - CPU/System Controller Board Component I.D. Diagram