Emerson ControlWave EFM 3808 - Appendix Z - Sources for Obtaining Material Safety Data Sheets (MSDS); Index

ControlWave Express Instruction Manual (CI-ControlWave Express)
Issue: Mar-2011 Index IND-1
Index
A
ACCOL3 Firmware Library ................................. 1-7
address
default IP ........................................................ 4-2
Analog Inputs...................................................... 3-8
Analog Output..................................................... 3-9
B
Backup battery
description ...................................................... 1-4
disconnecting.................................................. 5-7
jumper W3 .................................................... 2-10
removing/replacing......................................... 5-7
Backups .............................................................. 4-3
Battery
replacing......................................................... 5-6
Boot FLASH memory
amount............................................................ 1-4
C
Cables
RS-232 ......................................................... 2-14
RS-485 ......................................................... 2-19
Shielding......................................................... 3-4
Checking
LEDs............................................................... 5-8
Class I, Division 2 ........................................2-3, A-1
Communication Ports
defaults........................................................... 4-2
Ethernet........................................................ 2-21
RS-232 ......................................................... 2-14
RS-485 ......................................................... 2-19
Communications
Loop-back Test....................................5-14, 5-15
protocols supported........................................ 1-8
ControlWave project
downloading ................................................... 4-3
Core Updump ................................................... 5-16
CPU/System Controller board
battery backup................................................ 5-7
description ...................................................... 1-3
Jumpers........................................................ 2-10
removing......................................................... 5-5
switches.......................................................... 2-8
D
Defaults
Comm Ports.................................................... 4-2
Diagnostic software .......................................... 5-12
Disconnecting RAM Battery................................ 5-7
Discrete Inputs.................................................... 3-6
Discrete Outputs ................................................. 3-7
Display/Keypad................................................. 2-22
Downloading
the ControlWave project................................. 4-3
E
Environmental specifications .............................. 2-2
Ethernet Port..................................................... 2-21
F
Features.............................................................. 1-1
Field repair.......................................................... 5-5
Figures
1-1. ControlWave Express Component
Identification ................................................. 1-3
1-2. ControlWave Programming Environment 1-6
2-1. Co
ntrolWave Express Component
Identification ................................................. 2-2
2-2. ControlWave Express dimensions .......... 2-5
2-3. CPU/System Controller Board Component
I.D. Diagram ................................................. 2-7
2-4. CPU/ System Controller Board (TB1 & TB2)
Power Wiring.............................................. 2-13
2-5. Male DB9 9-Pin Connector ................... 2-15
2-6. Full-duplex and Half-duplex Cable........ 2-16
2-7. Full-duplex and Half-duplex Cable........ 2-17
2-8.Connection from an External Modem/Radio
to COM2 of the ControlWave Express....... 2-17
2-9. Full-duplex and Half-duplex Cable........ 2-18
2-10. RJ-45 Ethernet Connector .................. 2-21
2-11. Standard 10/100Base-T Ethernet Cable
(CPU Module to Hub)................................. 2-21
2-12. Point-to-Point 10/100Base T Ethernet
Cable .......................................................... 2-22
2-13 Optional 2-Button and 25-Button Keypads
.................................................................... 2-22
2-14 Display with No Keypad ....................... 2-23
3-1. Process I/O Board Component Identification
diagram......................................................... 3-3
3-2. Process I/O Board Wiring diagrams........ 3-5
3-3. Pulse Input Wiring diagram................... 3-10
3-4. 3-Wire RTD Temperature Input Wiring . 3-12
3-5. RTD Probe Installation/Removal diagram. 3-
13
3-6. 3808 Transmitter to ControlWave Express
RS-232 Comm. Cable Diagram.................. 3-14
3-7. 3808 Transmitter to ControlWave Express
RS-485 Comm. Cable ................................ 3-15
3-8. ControlWave Express to 3808s - RS-485
Network Diagram........................................ 3-15
4-1. Saving a Backup of Your Project ............ 4-4
5-1. HyperTerminal Mode Menu..................... 5-3
5-2. HyperTerminal (Ready to Download)...... 5-4