Emerson Dixell XB570L User Manual

1592006207 XB570L GB r1.1 23.03.2015 XB570L 1/20
XB570L
BLAST CHILLER - QUICK CHILL AND HOLD FUNCTION
CONTENTS
1. PLEASE READ BEFORE USING THIS MANUAL ....................................................................................... 1
2. SAFETY PRECAUTIONS ............................................................................................................................. 1
3. GENERAL FEATURES ................................................................................................................................. 2
4. MOUNTING & INSTALLATION ..................................................................................................................... 2
5. ELECTRICAL CONNECTIONS .................................................................................................................... 2
6. CONNECTIONS ............................................................................................................................................ 2
7. FRONTAL PANEL......................................................................................................................................... 1
8. QUICK START .............................................................................................................................................. 1
9. HOW TO SELECT A CYCLE ........................................................................................................................ 6
10. PARAMETERS ............................................................................................................................................. 7
11. HOW A CYCLE IS DONE. .......................................................................................................................... 10
12. INSTALLATION AND MOUNTING ............................................................................................................. 12
13. XB07PR - PRINTER (OPTIONAL) .............................................................................................................. 13
14. ELECTRICAL CONNECTIONS .................................................................................................................. 14
15. TTL SERIAL LINE ....................................................................................................................................... 15
16. USE OF THE PROGRAMMING “HOT KEY “ ............................................................................................. 15
17. ALARM SIGNALS ....................................................................................................................................... 15
18. TECHNICAL DATA ..................................................................................................................................... 16
19. STANDARD VALUE OF THE CYCLES. ..................................................................................................... 16
20. STANDARD VALUES OF THE PARAMETERS. ........................................................................................ 17
1. PLEASE READ BEFORE USING THIS MANUAL
• This manual is part of the product and should be kept near the instrument for easy and quick
reference.
• The instrument shall not be used for purposes different from those described hereunder. It cannot be
used as a safety device.
• Check the application limits before proceeding.
• Dixell Srl reserves the right to change the composition of its products, even without notice, ensuring
the same and unchanged functionality.
2. SAFETY PRECAUTIONS
• Check the supply voltage is correct before connecting the instrument.
• Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden
temperature changes with high atmospheric humidity to prevent formation of condensation
• Warning: disconnect all electrical connections before any kind of maintenance.
• Fit the probe where it is not accessible by the End User. The instrument must not be opened.
• In case of failure or faulty operation send the instrument back to the distributor or to “Dixell S.r.l.” (see
address) with a detailed description of the fault.
• Consider the maximum current which can be applied to each relay (see Technical Data).
• Ensure that the wires for probes, loads and the power supply are separated and far enough from each
other, without crossing or intertwining.
• In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel
with inductive loads could be useful.

Emerson Dixell XB570L Specifications

General

Brand	Emerson
Model	Dixell XB570L
Category	Chiller
Language	English

Summary

1. Please Read Before Using This Manual

2. Safety Precautions

4. Mounting & Installation

5.1 Probes Connection

Guidelines for connecting temperature probes correctly.

8. Quick Start

8.2 Keyboard in Stand-by

How Modify a Cycle

How to Modify the Room Set Point

9. How to Select a Cycle

9.1 How to Modify a Cycle

10. Parameters

Regulation Parameters

Parameters related to temperature control and regulation.

Probes Parameters

Parameters for probe calibration and presence settings.

10. Parameters (Continued)

Auxiliary Relay Configuration

Defrost Parameters

Parameters related to defrost cycle types and timings.

Second Relay Management

Fans Parameters

Parameters controlling fan operation modes during cycles.

Auxiliary Output Management

Temperature Alarms

Parameters for setting temperature alarm thresholds and delays.

11. How a Cycle Is Done

11.1 Configurable Cycle Parameters

Details on parameters for customizing cycle phases.

11.2 How to Use the Insert Probes

11.3 Example of a Blast Chiller Cycle

12. Installation and Mounting

12.1 Cut Out Dimensions

Specifies the required dimensions for the panel cut-out.

12.2 Mounting Procedure

Illustrates the physical mounting process of the instrument.

13.3 Connection to the XB570L – XB07PR

14. Electrical Connections

14.1 Probe Connections

16. Use of the Programming "Hot Key "

17. Alarm Signals

18. Technical Data

19. Standard Value of the Cycles.

19. Standard Value of the Cycles. (Continued)

20. Standard Values of the Parameters.

20. Standard Values of the Parameters. (Continued)