ENFORCER SK-1011-SDQ - Programming Functions; Programming the Egress Delay;Warning; Quick Programming Guide

3
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Quick Programming Guide:
This page is for installers looking to do a basic installation and programming of the keypad.
For more in-depth installation and programming instructions, see the Table of Contents on page 4.
Programming Tips:
• The master, super user, visitor, and user codes cannot be the same.
• $ÀDVKLQJDPEHU/('LQGLFDWHVWKHNH\SDGLVLQVWDQGE\PRGH$VROLGDPEHU/('LQGLFDWHVWKH
keypad is in programming mode.
• If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see pages 19~20).
Programming Instructions:
Follow the instructions below if the following covers your needs:
• A new master code.
• A single 4-digit user code for all users.
• One output to unlock a door.
• A 3-second delay time in opening the door after the output is activated.
1. Turn off the beeping before the 1-minute power-up period ends:

2. (QWHU3URJUDPPLQJ0RGH

NOTE:  is the default master code
3. Change the master code:
[[[[
NOTE: [[[[ is the new master code.
4. Set the user code to operate the output (unlock the door):
[[[[
NOTE: FKRRVHVXVHU,'RISRVVLEOHXVHUVa
;;;;LVWKHQHZXVHUFRGHIRUXVHU,'
5. Set the output delay time (skip this step if the default value of 5 seconds is acceptable):

NOTE:  sets the output delay time for 3 seconds.
6. ([LW3URJUDPPLQJ0RGH

22
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Egress Delay/Warning (continued):
NOTE: When the egress button is programmed to hold for a delay time before the door is
released, it is important to put a sign near the egress button to notify users of the
delay time.
Delay Time:
•

±1RGHOD\WLPHGHIDXOW7KHRXWSXWRSHUDWHVLPPHGLDWHO\ZKHQWKHHJUHVVEXWWRQLV
pressed.
•

to

±(JUHVVEXWWRQGHOD\WLPH7KHGHOD\WLPHFDQEHVHWIURPWRVHFRQGV7KLV
tells the keypad how long to wait after the egress button is pressed before activating the output.
Examples:
1. 0RPHQWDU\PRGH±3UHVVWKHHJUHVVEXWWRQDQGWKHNH\SDGZLOOEHHSIRUVHFRQGVEHIRUHWKH
output activates:

2. Hold button to activate ±3UHVVDQGKROGWKHHJUHVVEXWWRQIRUVHFRQGVDQGWKHNH\SDGZLOO
beep for those 10 seconds before the output activates:

3. 5HWXUQWRGHIDXOWVHWWLQJ±3UHVVWKHHJUHVVEXWWRQWRDFWLYDWHWKHRXWSXWZLWKQREHHSLQJRU
delay:

NOTE: For safety and to avoid confusion, when a delay or a press-and-hold delay is
SURJUDPPHGSOHDVHSRVWDQRWLFHQHDUWKHHJUHVVEXWWRQVXFKDV³3UHVVDQGKROGWKH
button for 5 seconds or until the door is unlocked.”