ENFORCER SK-1011-SDQ - Programming Specific Features; Programming User Code Entry Mode; Programming Keypad Sounds; Programming Output Relay Activation Sounds

5
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Features:
6SHFLÀFDWLRQV
Operating voltage a9$&9'&
Current draw
DW9'&
Standby 15mA
Keypress 30mA
Output 1 active 55mA
7RWDOPD[FXUUHQWGUDZ 90mA
Outputs
Form C $#9'&
Tamper P$#9'&
(JUHVVLQSXW 12*URXQG
Operating temperature -4°~158° F (-20°~70° C)
Operating humidity a1RQFRQGHQVLQJ
'LPHQVLRQVLQFOXGLQJEDFNER[
45⁄8´[7⁄8´[½´[[PP
Weight 6-oz (170g)
• a9$&9'&$XWRDGMXVWLQJRSHUDWLRQ
• 8SWRSRVVLEOHXVHUFRGHVa
• 8SWRaSRVVLEOHWHPSRUDU\YLVLWRU
codes, which can be programmed for one-
time or limited-time use (1~99 hours)
• 2XWSXW)RUP&UHOD\$#9'&PD[
• Output can be programmed to activate for up
to 99,999 seconds (nearly 28 hours)
• 7DPSHURXWSXW1&'U\FRQWDFW
P$#9'&PD[
• 0RXQWVWRDVWDQGDUGVLQJOHJDQJEDFNER[
VXUIDFHPRXQWEDFNER[LQFOXGHG
• All features are programmed directly from the
NH\SDG1RQHHGIRUDQH[WHUQDOSURJUDPPHU
• ((35200HPRU\SURWHFWVSURJUDPPHG
information in case of power loss
• (JUHVVLQSXWOHWVXVHUVH[LWWKHSUHPLVHV
without keying in the code
Overview:
Parts List:
[.H\SDG
[%DFNER[
[,QVWDOODWLRQVFUHZV
[0RXQWLQJVFUHZV
['LRGH
[0DQXDO
20
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the User Code Entry Mode (continued):
Programming the Keypad Sounds:
Some of the keypad sounds can be programmed off:
• .H\SDGDXGLEOHPRGH±$OOWKHNH\SDG¶VVWDWXVEHHSVDUHHQDEOHG
• Keypad silent mode – The successful key entry beep (1 beep) and the unsuccessful user code
entry beeps (5 beeps) are disabled. However, the warning and power-up delay beeps remain
DFWLYH7KLVSURYLGHVIRUDTXLHWHUZRUNHQYLURQPHQW
To Program:
• To enable keypad audible mode (default):

• To enable keypad silent mode:

NOTE: This programming function only impacts the keypad sounds. It does not impact the output
UHOD\DFWLYDWLRQVRXQGVVHH³3URJUDPPLQJWKH2XWSXW5HOD\$FWLYDWLRQ6RXQGV´EHORZ
To Program:
• For auto entry mode:

• For manual entry mode (default):

NOTE: If the keypad was previously programmed for manual code entry mode and then is
UHSURJUDPPHGIRUDXWRHQWU\PRGHDQ\FRGHVZKRVHOHQJWKH[FHHGVWKHQXPEHURI
digits of the master code will no longer operate the keypad. However, if the keypad is
reprogrammed for manual entry mode, the longer codes will again operate the keypad.
Programming the Output Relay Activation Sounds:
The keypad output sounds can be programmed for one of three modes:
• 1REHHSV– The keypad will not beep when the output is activated:

• 1-second beep (default) – The keypad will beep for 1 second when the output is activated:

• 2 short beeps – The keypad will beep twice when the output is activated:

NOTE: This programming function only impacts the output relay activation sounds. It does not
LPSDFWWKHNH\SDGVRXQGVVHH³3URJUDPPLQJWKH.H\SDG6RXQGV´DERYH