Enviro PRO-CS-1044 - User Manual

Questions and Answers

L
Lauren WellsAug 2, 2025
What to do if water pressure is slowing immediately after Enviro PRO-CS-1044 Water Dispenser installation?
- J
  Jennifer MendozaAug 2, 2025
  Avoid high flow rates from bathtubs, utility sinks, hose bibs, multi-headed showers, body sprayers, or anything considered high flow for the first 72 hours after installation. If you suspect a carbon blockage of the top basket due to a high-flow situation within the first 72 hours, turn off any running water for at least 10 minutes to clear the blockage, then resume using water at low or normal flow rates.
K
Kelly MorrisAug 7, 2025
What to do if Enviro PRO-CS-1044 Water Dispenser water pressure is slowing?
- F
  foleydonnaAug 8, 2025
  It is recommended to replace the Sediment Filter every 6-9 months, depending on the amount of sediment in your water supply. If your system has been working properly and the pressure is slowing, check the Sediment Filter and replace it if necessary.
J
jacksonshellyAug 13, 2025
Why is the pressure dropping off during the carbon wash of my Enviro PRO-CS-1044 Water Dispenser?
- M
  Michael JohnsonAug 13, 2025
  The pressure may drop off during the carbon wash because there is air trapped in the carbon bed. To resolve this, turn the water off and let the tank sit for about 30 minutes to allow the carbon to settle. If the pressure drops again, let the system stand for 72 hours. After 72 hours, continue the carbon wash by slowly turning the water supply back on.
T
traceybowmanAug 19, 2025
What to do if water is leaking at the top of the Enviro Water Dispenser tank?
- D
  Daniel MaysAug 19, 2025
  You may need to tighten the head of the tank. Turn the head to tighten it, ensuring it is snug but not overtightened. The tank head is pre-installed hand-tight, so avoid overtightening.
M
mccartyashleyAug 26, 2025
Why does Enviro Water Dispenser water appear grey or cloudy?
- C
  Christopher HansonAug 26, 2025
  Water may appear grey or cloudy for the first seven to ten days after installation due to extra carbon dust.

Summary

Product Operation and Specifications

Water Conditions For Operation - Natursoft Pro Systems

Guidelines for water quality, including hydrogen sulfide, hydrocarbons, phosphates, and copper levels for optimal system performance.

Complete Parts List

Installation Overview

Pre-Installation Steps

Covers general pre-installation requirements and specific instructions for bypass valve installation.

Carbon Tank Soak

Carbon Tank Wash

Installation

Pre-Filter System Installation

Detailed instructions for assembling and installing the pre-filter system.

Water Filter and Softener Tank Installation

Steps for installing the Whole House Water Filter and Salt Free Water Softener/Conditioner tanks.

Media Soak and Flush

Procedures for soaking and flushing the system media.

What to Expect with your New Salt Free Water Softener;Conditioner

Post-Installation Experiences

Describes changes in water feel, mineral silt, and interactions with detergents.

Dishwasher and Hot Water Heater Considerations

Advice on dishwasher detergent and optional hot water heater cleaning.

Care and Cleaning

Sediment Filter Maintenance

Guidance on replacing the sediment filter and its recommended service interval.

Troubleshooting

Warranty and Registration

Warranty Terms and Guarantees

Details the limited lifetime warranty, limitations, and performance guarantees.

Warranty Registration Process

Instructions on how to register the product for warranty validation.

Product Certifications

Enviro PRO-CS-1044 Specifications

General

Model	PRO-CS-1044
Brand	Enviro
Installation	Freestanding
Type	Water Dispenser
Water Temperature	Hot and Cold
Cooling System	Compressor
Hot Water Temperature	185°F (85°C)
Voltage	115V
Material	Stainless Steel