Epson FX-2190IIN User Manual

!
Caution:
Whenever you turn off the printer, wait at least five seconds before turning it back on;
otherwise you may damage the printer.
2. To run the test using the Draft font, turn on the printer while holding down the LF/FF button. To
run the test using the printer’s letter-quality fonts, turn on the printer while holding down the
Load/Eject button. Either self test can help you determine the source of your printing problem;
however, the draft self test prints faster than the letter-quality test.
3. When using single-sheet paper, load paper in the printer.
After a few seconds, the printer loads the paper automatically and begins printing the self test. A
series of characters is printed.
Note:
To temporarily stop the self test, press the Pause button. To resume the test, press the Pause button
again.
4. To end the self test, press the Pause button to stop printing. If paper remains in the printer, press
the Load/Eject button to eject the printed page. Then turn off the printer.
!
Caution:
Do not turn off the printer while it is printing the self test. Always press the Pause button to stop
printing and the Load/Eject button to eject the printed page before you turn off the printer.
Printing Hex Dump
If you are an experienced user or a programmer, print a hexadecimal dump to isolate communication
problems between the printer and your software program. In hex dump mode, the printer prints all
data it receives from the computer as hexadecimal values.
You can print a hex dump using either single sheets or continuous paper. See “Loading Continuous
Paper” on page 21 or “Loading Single Sheets” on page 44 for instructions on how to load paper.
Note:
❏ The hex dump feature is designed for a connection with DOS-based PC.
❏ Use paper that is at least 210 mm (8.3 inches) wide, such as A4 or letter size paper.
Follow these steps to print a hex dump:
FX-890II/FX-890IIN/FX-2190II/FX-2190IIN User’s Guide
Troubleshooting 114

Epson FX-2190IIN Specifications

General

Color	-
Bitmap fonts	Draft, OCR-B, Roman, Sans Serif
Character sets	Italic, PC437, PC850, PC858, Roman 8
Character pitch	10, 12 cpi
Built-in barcodes	CODABAR (NW-7), Code 128 (A/B/C), Code 39, Industrial 2/5, Matrix 2/5, POSTNET, UPC-A, UPC-E
Maximum resolution	240 x 144 DPI
Number of characters	42
Maximum number of copies	6 copies
Maximum print speed (NLQ)	115 cps
Maximum print speed (draft)	612 cps
Maximum printing width (columns)	136
Print yield	12 characters
Print direction	Bi-directional
Ribbon life (black, draft)	12 million characters
Mean time between failures (MTBF)	25000 h
Sustainability certificates	ENERGY STAR
Standard interfaces	Ethernet, Parallel, USB
Paper tray media types	Envelopes
Single sheet thickness range	0.06 - 0.14 mm
Continuous paper thickness range	0.46 - 0.46 mm
Multi-part paper thickness range	0.12 - 0.46 mm
AC input voltage	198-264 V
Power consumption (standby)	10 W
Power consumption (typical)	55 W
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	5 - 35 °C
Storage relative humidity (H-H)	30 - 60 %
Operating relative humidity (H-H)	10 - 80 %
Product color	Black
Country of origin	Indonesia
Sound pressure level (printing)	55 dB
Needles	18 (2 x 9)
Print technology	Dot matrix
Connectivity technology	Wired
Pallet width	800 mm
Pallet height	2250 mm
Pallet length	1200 mm
Pallet weight	0 g
Pallet width (UK)	1000 mm
Quantity per pallet	14 pc(s)
Quantity per pallet (UK)	21 pc(s)
Quantity per pallet layer	2 pc(s)
Harmonized System (HS) code	84433210
Quantity per pallet layer (UK)	3 pc(s)
Package depth	735 mm
Package width	455 mm
Package height	300 mm
Package weight	12160 g
Quantity per pack	1 pc(s)

Weight and Dimensions

Depth	375 mm
Width	612 mm
Height	177 mm