Where to get help
Internet support
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities
and documentation, get FAQs and troubleshooting advice, or e-mail
Epson with your questions.
Visit http://www.presentersonline.com to access tips, templates, and
training for developing successful presentations.
Speak to a support representative
To use the Epson PrivateLine
®
Support service, call (800) 637-7661
and enter the PIN on the included Epson PrivateLine Support card.
This service is available 6
AM to 6 PM, Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak
with a projector support specialist by dialing one of the following
numbers. (Toll or long distance charges may apply.)
U.S.: (562) 276-4394, 6
AM to 6 PM, Pacific Time, Monday-Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday-Friday
Days and hours of support are subject to change without notice.
Purchase supplies and accessories
You can purchase screens, carrying cases, and other accessories
from an Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
5 Adjust the image
1 To raise the image, lift the front of the
projector and turn the front feet to adjust
the position of the projected image.
2 Open the lens access door.
3 Turn the focus ring to sharpen
the image.
Turn the zoom ring to reduce or
enlarge the image.
4 If your image looks like or , first make sure the projector
is facing the screen squarely. Then, if necessary, press the
or
buttons on the projector’s control panel until the image is corrected.
5 To select the best color mode, press the Color Mode button on the
remote control repeatedly to move through the options.
See your User’s Guide on the CD-ROM for more information about
image adjustments.
6 Install your User’s Guide
and register your projector
1 Insert the PowerLite 6110i CD-ROM in your drive. If the installer
doesn’t open automatically, double-click the Epson CD-ROM icon,
then double-click the Epson installer icon.
2 Follow the instructions on the screen to register.
NOTE
You can also register at www.epson.com/webreg.
3 After you register the projector, click User’s Guide to install it.
(If you don’t already have Adobe
®
Reader,
®
click Adobe Reader
[Windows
®
only] and follow the on-screen instructions to install it.)
4 When you’re done, click Exit.
To open your User’s Guide, double-click the PL 6110i User’s Guide
icon on your desktop.
4 Plug in and turn on
1 Connect the power cord to the projector and plug the other end
into an electrical outlet.
The
Power light on the projector turns orange.
2 Turn on your computer or video source.
3 Press the
Power button on the projector or remote control.
The projector beeps, the
Power light flashes green, and the
projector lamp comes on in about 5 seconds. The
Power
light stays green.
4 Start your video or presentation. If you have connected more
than one video source, use the Source Search button on the
projector or remote control to select the one you want to watch.
NOTE
If your image does not appear on the screen, see the
“Troubleshooting” section for help.
Turning off the projector
1 If you’re using a computer, shut it down first, while you can
still see the display.
2 Press the
Power button on the projector or remote control.
3 When you see the confirmation message, press the
Power
button again. The
projector beeps twice and the
Power
light turns orange.
With Epson’s Instant Off
®
technology, there’s no cool-down
period. When you’re done, just unplug the projector.
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on
your computer or video source, check the following:
Make sure the Power light on the projector is green and not
flashing.
Make sure the cables are connected correctly. (See the User’s Guide
for more information.)
If you’ve connected more than one video source, you may need
to press the Source Search button on the projector or the remote
control to select the one you want to watch. (Allow a few seconds
for the image to appear after pressing it.)
If the projector and the notebook don’t display the
same image
If you’re using a Windows notebook:
Hold down the Fn key and press the function key (such as
or CRT/LCD) that lets you display on an external monitor. On most
systems, the
or CRT/LCD key lets you toggle between the
LCD screen and the projector, or display on both at the same time.
Check your monitor settings to make sure both the LCD screen
and the external monitor port are enabled. From the Control
Panel, open the Display utility. Click the Settings tab, then click
Advanced. The method for adjusting the settings varies by brand;
you may need to click a Monitor tab, then make sure the external
Monitor port is set as your primary display and/or enabled. See
your computer’s documentation or online help for details.
If you’re using a Macintosh
®
notebook with OS X:
1
From the Apple
®
menu, select System Preferences, then click
Display or Displays.
2 Select VGA Display or Color LCD, click Arrangement or Arrange,
and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a trademark of
Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is
a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those marks.
© 2007 Epson America, Inc. 9/07
Printed in XXXXXX CPD-24718
Focus
Zoom
Power light
Color Mode button
4112470 Rev.0
1-B C
4112470 Rev.0
1-B M
4112470 Rev.0
1-B Y
4112470 Rev.0
1-B K
To Previous Page
Loading...
