Eraser M700 Series - Run Job Execution Status; Create;Edit Job

1110
ManualModeMenu
JOG Feed Material
CUT Cut Material
EDIT Change Params
LENGTH 0.000in
JOG: Press Jog to feed material to a
predetermined length.
NOTE: Pressing the + key will advance the
material incrementally as displayed in the
LENGTH line and pressing the – key will
retract the material.
CUT: Press CUT to make a manual cut (using
default cutting parameters). Pressing the CUT
key will also zero out the LENGTH line.
The Edit Feed & Cut screen allows the user
to set or change the default parameters for
the JOG and CUT settings. These parameters
can be changed at any time. The last entered
values will be stored, even when the unit is
powered off.
Pressing the EDIT key will display the Edit
Feed & Cut screen:
ManualModeMenu;EditFeed&Cut
JOG Length > 1 .000in
Feed Rate 3
Cut Rate 5
Cut Time 1.0sec
Jog Length: This function adjusts the
feed length value associated with the JOG
key. Using the keypad, enter a value from
0.1 to 99,999. The Units can toggled (and
converted) between inches and centimeters
by pressing the + or – key. Press ENTER to
advance to the next line.
NOTE: See instructions under #4 Create/Edit
Job for information on Feed Rate, Cut Rate
and Cut Time. The Jog Length parameter
is not applicable when a Feeder Module
is not connected to the system. Similarly,
the Cut Rate and Cut Time parameters are
not applicable when a pneumatic powered
Module is connected to the system.
ESC back to the Manual Mode menu or
further to the Main Menu.
#3 Run Job:
The Run Job menu option is used to run
preprogrammed jobs. When running a Job,
it is recommended to make a manual feed
and/or cut (as per instructions under #2
Manual Mode) prior to running the Job to
ensure the rst piece of processed material
returns the desired length.
NOTE: All doors must be closed and the
downstream Endcap installed for the system
to function.
Pressing the 3 key (from the Main Menu)
will display the Run Job menu screen:
RunJobMenu
Enter Job:_
Job [001] xxxxxxxxxx
Job [002] xxxxxxxxxx
Job [003] (empty)
At this screen the user may scroll through the
list of jobs using the + and – keys to page
down and page up respectively.
Using the keypad, enter a preprogrammed
Job number (1-100) and press ENTER.
Once a Job has been selected to run, the Job
Status screen will display the job number,
units and the job name. Additionally,
the rst and last programmed Batch (B)
along with their respective Lengths (L) and
Quantities (Q) will be displayed:
RunJobMenu;JobStatus
Job [xxx] Units [in]
[xxxxxxxxxxxxxxxx]
BXX L:X.XXX
11
10
Q:XXXXX
BXX L:X.XXX
Q:XXXXX
To run the Job, press RUN.
While a Job is running, the Running Status
screen is displayed.
RunJobMenu;RunningStatus
Job [xxx] Running
[xxxxxxxxxxxxxxxx]
Batch: X/X
Count: XXXXX/XXXXX
The Running Status screen will show the
following statuses: Running, Paused, or
Complete.
Also displayed are the current Batch number
and the Count of how many pieces have
been processed of the programmed quantity
(ex. 1/5 = the rst of 5 programmed pieces).
If the Job is set up for Continuous Mode,
the Count will not display a programmed
quantity (ex. 1/Cont. = the rst of an
indenite number of pieces).
While running, the Batch eld will alternate
with a real time Feed Length readout. Note:
If the Job is programmed in such a way that
doesn’t allow for enough time for the Feed
Length to display, this readout may not be
displayed.
When a Job is paused, the Paused Status
screen is displayed:
RunJobMenu;PausedStatus
Job [xxx] Paused
RESUME PRESS RUN
Batch: X/X
Count: XXXXX/XXXXX
NOTE: To pause a Job before it is completed,
press the ESC key and it will pause the Job
after nishing the piece in process.
To resume the Job, press the RUN key. ESC
will not stop the machine from feeding or
cutting mid-process.
To stop the machine for safety reasons
press the Emergency Stop Button. This will
immediately stop all feeding or cutting in
process.
When a Job is complete, the Complete Status
screen is displayed:
RunJobMenu;CompleteStatus
Job [xxx] Complete
[xxxxxxxxxxxxxxxx]
BXX
Count: XXXXX/XXXXX
If desired, the user can press RUN to repeat
the same Job or ESC back to the Run Job
menus or further to the Main Menu.
#4 Create/Edit Job:
The Create/Edit Job menu option is used
to create new preprogrammed Jobs and
Batches or edit existing preprogrammed
Jobs and Batches.
Batches: A Batch contains the information
for measuring and cutting identical sets
of material. It consists of a Length and
a Quantity as well as other feed and cut
parameters (described ahead in further
detail in the #4 Create/Edit Job section).
Jobs: A Job is a set of up to 20 Batches. Up
to 100 Jobs can be programmed on the
M700C. A Job that does not contain any
Batches is called an Empty Job.
Pressing the 4 key (from the Main Menu) will
display the Create/Edit Job menu screen.
Note: If the Supervisor Password setting
is enabled, the Enter Supervisor Password
screen will display rst: