Eraser M700 Series - Default Chapter; Table of Contents

2
EU Declaration of Conformity
Denitions and Labels
Safety Precautions
Quick Start Instructions
M700 Modular Series
Concept
Safety Features
System Technical Data
System Performance
M700 Control Module (AR3300)
Overview
Technical Data
Performance
Power
Fuses
Setup and Operation
#1 System Status
#2 Manual Mode
#3 Run Job
#4 Create/Edit Job
#5 Supervisor Password Settings
#6 Change Default Settings
Supervisor Password Reset
M700F Feeder Module (AR3400)
Overview
Technical Data
Performance
Power
Required Parts
Replacement Parts
3
4
5
7
7
8
15
16
17
18
Bushing Installation
Module Assembly
Belt Adjustment
Belt Replacement
M700 Cutter Modules
(See applicable module inserts)
Care and Maintenance
Troubleshooting Guide
Glossary of Terms
TABLE OF CONTENTS
3
2
EU Directive: 2006/95/EC Low Voltage
EC 60204-1 Revision / Edition: 5.1 Chg.: Date:
02/00/09 SAFETY OF MACHINERY - ELECTRICAL
EQUIPMENT OF MACHINES - PART 1: GENERAL
REQUIREMENTS
BS EN 60204-1 Revision / Edition: 06 Chg.: W/
CRGD Date: 05/31/10
Reference Specs
ISO/TR 14121-2:2012 Safety of machinery
-- Risk assessment -- Part 2: Practical guidance
and examples of methods
BS EN ISO 13849-1 Revision / Edition: 09
Chg.: W/ CRGD Date: 08/31/10 SAFETY
OF MACHINERY - SAFETY-RELATED PARTS
OF CONTROL SYSTEMS PART 1: GENERAL
PRINCIPLES FOR DESIGN
BS EN ISO 13849-2 Revision / Edition: 12
Chg.: Date: 10/31/12 SAFETY OF MACHINERY -
SAFETY-RELATED PARTS OF CONTROL SYSTEMS
PART 2: VALIDATION
BS EN ISO 13850 Revision / Edition: 08 Chg.:
Date: 09/30/08 SAFETY OF MACHINERY -
EMERGENCY STOP - PRINCIPLES FOR DESIGN
BS EN ISO 4414 Revision / Edition: 11 Chg.:
Date: 07/31/11 PNEUMATIC FLUID POWER.
GENERAL RULES AND SAFETY REQUIREMENTS
FOR SYSTEMS AND THEIR COMPONENTS
EU Directive: 2006/423/EC Machinery
BS EN ISO 12100 Revision / Edition: 10
Chg.: W/ CRGD Date: 01/31/11 SAFETY OF
MACHINERY - GENERAL PRINCIPLES FOR
DESIGN - RISK ASSESSMENT AND RISK
REDUCTION
Reference Specs
BS EN ISO 13857 Revision / Edition: 08 Chg.:
Date: 04/30/08 SAFETY OF MACHINERY -
SAFETY DISTANCES TO PREVENT HAZARD ZONES
BEING REACHED BY UPPER AND LOWER LIMBS
DIN EN 349 Revision / Edition: 08 Chg.:
CRGD Date: 01/00/09 SAFETY OF MACHINERY
- MINIMUM GAPS TO AVOID CRUSHING OF
PARTS OF THE HUMAN BODY
EU Directive: 2004/108/EC
Electromagnetic Compatibility (EMC)
EN 61000-6-2: 2005-08: Electromagnetic
compatibility (EMC) - part 6-2: Generic
standards: immunity for industrial
environments
EN 61000-6-3: 2007-01, Electromagnetic
compatibility (EMC) - part 6-3: Generic
standards: Emission standard for residential,
commercial and light -industrial environments
Reference Specs
EN 61000-4-2 Electromagnetic compatibility
(EMC) - Part 4-2: Testing and measurement
techniques - Electrostatic discharge immunity
test
EN 61000-4-6 Electromagnetic compatibility
(EMC). Testing and measurement techniques.
Immunity to conducted disturbances, induced
by radio-frequency elds (British Standard)
EN 61000-4-3 Electromagnetic compatibility
(EMC) - Part 4-3 : Testing and measurement
techniques - Radiated, radio-frequency,
electromagnetic eld immunity test
EN 61000-4-4 Electromagnetic compatibility
(EMC) - Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst
immunity test
EN 61000-4-5 ELECTROMAGNETIC
COMPATIBILITY (EMC) - PART 4-5: TESTING
AND MEASUREMENT TECHNIQUES - SURGE
IMMUNITY TEST
EN 61000-4-11 Electromagnetic compatibility
(EMC) - Part 4-11: Testing and measurement
techniques - Voltage dips, short interruptions
and voltage variations immunity tests”
DECLARATION OF CONFORMITY
We hereby declare that the machine complies with all the relevant specications of the
following EU Directives:
3