76
DO NOT USE IN DANGEROUS ENVIRONMENTS
Do not use or locate machine in high-humidity environments, or expose to rain. Keep work
areas well lighted.
WEAR PROPER APPAREL (This is not an all-inclusive list.)
Do not wear loose clothing, such as gloves, neckties, rings, bracelets, necklaces or any other
clothing or jewelry that might get caught in moving parts. Wear protective hair covering to
contain long hair. Non-slip footwear is recommended.
DO NOT OVERREACH
Maintain proper footing and balance at all times.
MAINTAIN BLADES WITH CARE
Keep blades sharp and clean for optimal performance. Follow instructions for changing
blades and accessories.
DISCONNECT MACHINE FROM POWER SUPPLY
Unplug the unit before servicing and when changing accessories.
DO NOT EXCEED THE UNIT’S MAXIMUM MATERIAL SPECIFICATIONS
Eraser’s warranty will be null and void if machine has been used in any manner that is
contrary to these instructions.
CHECK FOR DAMAGED PARTS
Before continued use of the machine, the guard and all moving parts should be carefully
inspected to ensure that nothing is damaged.
Ensure proper alignment of moving parts. Check for any binding of moving parts, breakage
of parts, and any other condition(s) that may affect operation. Any damaged part(s) should be
properly repaired or replaced prior to any continued use of the machine.
ONLY ALLOW TRAINED AND QUALIFIED PERSONNEL TO OPERATE UNIT
Always keep a copy of the operating manual within reach of the machine. The pneumatic
powered cutters require 90 psi of air. Proper training on pneumatic equipment is required.
USE RECOMMENDED ACCESSORIES ONLY
Consult the operation manual for recommended accessories. Use only parts supplied by
The Eraser Company, Inc. Use of improper accessories will void Eraser’s warranty and may
increase risk of injury. Using improper tools such as hammers or leveraging tools can
overtighten and destroy threaded parts; also may cause tools to slip or break causing
hand injury.
ALL REPAIRS SHOULD BE PERFORMED BY AN ERASER COMPANY REPRESENTATIVE ONLY
Unauthorized disassembly of the machine will void Eraser’s warranty. Anything that is done
to modify the machine in any way to override safety, will void all warranty. Covers may not be
removed in any way, otherwise the warranty will be null and void.
When using machinery, all safety precautions—including, but not
limited to, those listed above—should be followed to reduce the risks
of re, electric shock, and personal injury, and death.
IMPORTANT: No liability will be incurred by The Eraser Company for injury, death, or
property damage caused by a product which has been set up, operated, and/or installed
contrary to Eraser’s written operating manual or which has been subjected to misuse,
negligence, or altered by anyone other than The Eraser Company, or which has been used in
a manner or for a purpose for which the product was not designed.
7
QUICK START INSTRUCTIONS
M700 MODULAR SERIES
1. Install the proper size bushings for the
material being processed.
2. Open clamping latch on rear, align
module and close clamping latch.
Repeat for as many modules as necessary.
3. Insert Endcap into last module using same
technique as step 2.
4. Feed material from left to right through
the bushings and adjust feed belts as
needed (if applicable).
5. Close the door to the Feeder and/or
cutter module.
6. Plug in and turn on power to the Control
Module.
7. Program length, quantity, feed rate, cut
rate and/or cut time as needed.*
8. Make a manual cut to check cut quality
and make adjustments if needed.
9. If feeding manually, advance material to
length stop.
10. If using the Feeder Module, press run
and check length of rst piece and utilize
the feed adjust if needed.
CONCEPT:
The M700 Modular Series is a compact table
top system designed to cut various wire
and tubing material to repeatable accurate
lengths. A variety of swappable M700
modules, including a Control Module, Feeder
Module and a number of cutting modules, are
designed to quickly and seamlessly connect
and work together as either an automatic or
manual material processing system.
SAFETY FEATURES:
• Emergency Stop Button; located on
Control Module
• Latching Safety Doors with Coded Sensors;
located on all processing modules
• Transparent Module Windows; located on
all processing module doors
• Out of Material Sensor; located inside
Feeder Module
• System Endcap; installed into last connected
module’s interface connection
• Grounded power cord; supplied with
Control Module
SYSTEM TECHNICAL DATA:
Material Specications:*
Minimum system material size:
1/64” (0.4mm) OD
Maximum system material size:
1-1/8” (28.6mm) OD
Minimum feed/cut length: 0.100” (.254cm)
Maximum programmable feed/cut length:
99,999.0 (in or cm)
Maximum programmable quantity:
99,999 pieces
Feed/Cut Tolerances:*
Material Length
Under 2” (5.08cm): ±0.010 (±0.025cm)
Over 2” (5.08cm): ±1%
Squareness of cut: ±2°
*Specicationismaterialdependentand/or
dependentonde-reelingsystem
System Dimensions (L x W x H):
Control Module + 1 module: 16” x 16.75” x 8”
(40.64cm x 42.55cm x 20.32cm)
Control Module + 2 modules:16” x 24” x 8”
(40.64cm x 60.96cm x 20.32cm)
Operating Environment:
Operating Temperature: 32°F - 104°F
(0°C - 40°C)
Relative Humidity: @ 90%: 32°F - 70°F
(0°C - 21°C) @ 50%: 70°F - 104°F (21°C - 40°C)
Airow: Unobstructed and well ventilated
Intermittent Usage:
This system has no minimum intermittent duty
cycle limitations.
SYSTEM PERFORMANCE:
Supported Modes
Continuous Mode
Single Piece Flow Mode
*See programming instructions
To Next Page
Loading...