33
Stop the engine, disconnect the spark plug before proceeding and remove
key from ignition.
• MU80N: MULCHING KIT (picture 50)
• A special blade and a ejection-closing insert allow a ne cut of frequently
cut grass, helping its decomposition without needing any collection.
• MD803: SIDE DEFLECTOR (picture 51)
•
Allows ejection of the grass to the side. It is recommended in very
high grass or when collection is not necessary. A rst cut at maximum
cutting height and low drive speed followed by a second cut at nal
height insure a good nish.
• ANTI-PUNCHURE TYRE LIQUID (part number 28461)
• Introduced as prevention in the tyres inner tubes, this liquid repairs
instantaneously potential perforation.
• SEAT ARMRESTS MAC FOR MKHP AND MKHPF (pic-
ture 52)
• Armrest greatly improve driving comfort, in particulary when your
mower is being used on a slope. They are easy to attach to the seat
back rests by 4 screws.
• SPREADER MET (picture 53)
• Having a hopper capacity of 60 L, this wheel-driven distributing disc
spreader is ideal for spreading snow clearing salt or sand.
• MR80: TOWING HOOK FOR MKHE, MBHE, MHHE
AND MKHP (standard on MKM and MKHPF) (picture 54)
•
Allows to tow light loads according to following limits:
- 140 kg on the trailer axle (trailer + load)
- 20 kg upward or downward on the drawbar
- drive on slopes of 5° (8.7%) maximum
• CONTROL LEVER ML80 (pictures 55, 56 and 57)
• It allows the control of the accessory mounted on your mower.
• SNOW BLADE MV80N3 (picture 56)
• Designed for cleaning snow from aisles and outside areas. Adjustable
to the right or to the left.
• MOSS REMOVER MM103 (picture 57)
• Makes it possible to extract the moss from your lawn and collect it
directly with your mower.
• HOMOLOGATION KIT OMX80 (picture 58)
• It allows you to equip your mower with front and rear lighting allo-
wing it to travel on public roads.
• ANTI SCALP KIT MAS80 (not available on MKM and MKHPF)
(picture 59)
• The MAS80 reduces blade contact with the ground and allows the
deck to follow the contours of the ground during the cutting.
• BLADE (picture 60)
All models except MKHPF and MKM
• MZ80 : standard blade
28489 : cutting blade kit MZ80
• MZ80EX : lame export
52168 : cutting blade kit MZ80EX
• MZ80M : lame mulching
28447 : cutting blade kit MZ80M
MKM
• MC85MN : kit of 2 half blades
MKHPF
• MC85 : kit of 2
ails
ELECTRIC GRASSBOX EMPTYING KIT MVE80
• For a greater comfort of use, you can replace the lever for manual
emptying of the grassbox, using a device with an electric ram operated
by a switch mounted on the instrument panel.
All these accessories are accompanied with an instruction manual of
installation and use.
13• ACCESSORIES
• REAR WHEELS
- Stop the engine and remove the contactor key.
- Apply the parking brake.
- Secure the vehicle using chocks.
- Remove the wheel hub (a picture 48).
- Unscrew the 3 screws with a key 6 (thread 5) (b picture 48). Re-
move sidewards the two securing rings (c picture 48).
- Place a jack under the rear part of the chassis on the side where the
wheel needs to be replaced and lift until this wheel does not touch
the ground anymore (picture 49).
- Secure the machine by lying it on stable props. You can now re-
move the wheel from the shaft.
• For remounting, follow the same instructions in the opposite way. Do
grease the wheel shaft.
WARNING !
Do not lose the O shape key which ts in the wheel shaft.
• Check the screw tightness.
• Check the tyre pressure.
Front pressure:
1.5 bar for MKHP and MKHPF models
1.2 bar for other models
Rear pressure: 0.8 bar
DISPOSAL OF USED PNEUMATICS
It is forbidden to leave standing, to lay down or to burn pneumatics in
nature. Our dealer network has been informed about its obligation to
take back, free of charge, all used pneumatics from ETESIA ride on
mowers.
12• TROUBLESHOOTING
To Next Page
Loading...
