Excell PWZ0163100.02 - User Manual

Questions and Answers

J
jacksonkimberlyJul 30, 2025
Why is my Excell Pressure Washer not starting?
- J
  John BarnesJul 30, 2025
  Your Excell Pressure Washer might not be starting due to several reasons: there's no fuel, pressure build-up after a couple of pulls on the recoil starter, the choke lever is in the “No Choke” position, the spark plug wire isn't attached, the engine ON/OFF switch is in the OFF position, or the choke lever is in the “Choke” position on a hot engine. To resolve this, add fuel, squeeze the gun trigger to relieve pressure, move the choke to the “Choke” position, attach the spark plug wire, place the engine ON/OFF switch in the ON position, or move the choke to the “No Choke” position, respectively.
S
Sarah SilvaAug 3, 2025
What to do if my Excell Pressure Washer has no or low pressure on initial use?
- K
  Kristen JonesAug 3, 2025
  If your Excell Pressure Washer has no or low pressure upon initial use, it could be due to several factors. Ensure the high-pressure nozzle is installed correctly. Verify that the water supply is at least 5 GPM @ 20 PSI. Check for leaks at the high-pressure hose fitting, repairing them and applying sealant tape if needed. Inspect for any obstructions in the nozzle. Clean the water filter screen if it's clogged. Remove any air in the hose by disconnecting the water source, turning it on to remove air, then reconnecting. Ensure the choke lever is in the “No Choke” position. Also, make sure the high-pressure hose is under 100 feet. For the nozzle and spray wand usage, refer to the Operation Section; for nozzle cleaning, see the Maintenance section.
E
Ethan CopelandAug 7, 2025
What to do if my Excell PWZ0163100.02 has water leaking at the pump?
- J
  jorgebarnettAug 7, 2025
  If you notice water leaking at the pump of your Excell Pressure Washer, check for loose connections and tighten them. If the piston packing is worn, or if there are worn or broken O-rings, they should be replaced. Also, inspect the pump head or tubes for damage from freezing.
Y
ycookAug 11, 2025
Why does my Excell PWZ0163100.02 Pressure Washer have no or low pressure after a period of normal use?
- M
  Michelle PierceAug 12, 2025
  If your Excell Pressure Washer has no or low pressure after a period of normal use, it could be due to a worn seal or packing, worn or obstructed valves, or a worn unloaded piston. These parts should be replaced.
R
Richard FarmerAug 15, 2025
What to do if my Excell PWZ0163100.02 Pressure Washer won't draw chemicals?
- A
  Anne KimAug 15, 2025
  If your Excell Pressure Washer isn't drawing chemicals, make sure the low-pressure soap nozzle is installed. Check the chemical filter for clogs and clean it if necessary. Ensure the chemical screen is fully submerged in the cleaning solution. If the chemical is too thick, dilute it to the consistency of water. Avoid using an excessively long high-pressure hose; instead, lengthen the water supply hose. If there's chemical buildup in the injector, it should be cleaned or replaced.
V
Victoria CoffeyAug 20, 2025
What to do if my Excell PWZ0163100.02 Pressure Washer has water leaking at the gun/spray wand connection?
- D
  Dr. Jose MorrisAug 20, 2025
  If there's a water leak at the gun or spray wand connection of your Excell Pressure Washer, inspect the O-ring for wear or breakage and replace if needed. Also, check the hose connection and tighten it if it's loose.
D
Dr. Tanya Hernandez DVMAug 25, 2025
Why is my Excell PWZ0163100.02 pump pulsating?
- V
  Victoria LopezAug 25, 2025
  Your Excell Pressure Washer pump may be pulsating because the nozzle is obstructed. Refer to the Maintenance section for the correct procedure for nozzle cleaning.