26
OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at least one minute before starting to cook to direct fumes
and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours
and odours. By means of the Timer function, it is possible to set auto switch-off
function which will allow the hood to turn off automatically after 15 minutes of
operation.
WHICH SPEED IS TO BE SELECTED?
speed (1-3): maintains the circulation of clean air with low electricity consump-
tion.
speed (4-5): normal conditions of use.
speed (6-7): presence of strong odours and vapours.
speed (8-P): rapid disposal of odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The metal filters must be cleaned every 30 hours of operation.
The active carbon filters must be replaced every 18 months and replaced every
3 years.
For further details see the “MAINTENANCE” chap.
HOOD TOUCH PUSHBUTTON PANEL
+
Speed increase from 1 to…9 (up
to “P”).
Speed “P”: active only for a few mi-
nutes, then speed 9.
A
A: Hood operation automatic cycle
activation (A) according to plate
power.
A
Hood timer function.
Allows you to turn off the hood after
a set time
Automatic switch o: if all the bur-
ners are turned off, the hood stays
on for 5 minutes and then turns off
automatically
A
A
-->
A
+
A
A
-->
A
Carbon.Zeo lter alarm:
Maintenance after about 1500 hours
of use. The display shows “F”.
To reset the alarm: press the
key for 5 seconds
To Activate the alarm:
With the hood off, press the hood di-
splay for 5 seconds. The activation of
the Carbon.Zeo filter alarm function
is given by the visualization of F + A
on the display
To turn o the alarm:
With the hood off, press the hood di-
splay for 5 seconds. The deactivation
of the Carbon.Zeo filter alarm fun-
ction is given by the visualization of
only F on the display
If the pushbutton panel is completely inactive, before contacting
the Technical assistance service, disconnect power temporarily to
the appliance (about 5“), possibly by acting on the main switch, to
restore normal operation. If this measure has no eect, contact the Techni-
cal assistance service.
CLEANING AND MAINTENANCE
ATTENTION!
For cleaning, never use a steam equipment.
Before cleaning the cooker, make sure that it is at room temperature.
Always clean the cooker after each use with a specic cleanser for pyroceram.
Do not use products containing:
- corrosive agents (soda, acids, ammoniac).
- abrasive agents (dusts or paste).
Do not wash the aps in a dishwasher.
Do not use pointed or abrasive objects.
After cleaning, dry the appliance with a soft cloth.
USEFUL CARE TIPS
Clean your glassceramic cooktop regularly, preferably every time you use it.
Avoid using abrasive sponges or scouring agents.
Harsh chemical cleaners like oven sprays or stain removers are also unsuitable, as
are bathroom or household cleaners.
Accidents happen …
Do not allow the hot hob to come into contact with plastic, tin foil, sugar or
sugary food have fallen on the hot glass-ceramic cooktop. Please scrape it off
the hot surface as quickly as possible. If these substances melt, they can damage
the glass-ceramic cooktop.
Sparkling results in only three steps:
To thoroughly clean your glass-ceramic cooktop, first remove dirt and food with
a suitable metal scraper.
Once the glass-ceramic cooktop has cooled, put a few drops of a suitable clean-
er on it and rub it on with a paper towel or a clean cloth.
Then wipe the glass-ceramic cooktop with a damp cloth and dry it with a clean
cloth.
How do I identify a suitable glass-ceramic scraper?
• Scraper made of metal (won’t melt or catch fire)
• Scraper easy to lock / to unlock
• Blade is fixed precisely, it does not shift
• Blade is unbroken, clean and stainless
• Scraper certified by testing institute, if procurable (e.g. TÜV-GS seal)
• User manual and safety instructions available
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor inside
the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters (F) (at least once a month)
leaving them to soak in boiling water and cleaning solution for 1 hour, taking
care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling
them.
Washing in a dishwasher is permitted.
To extract and insert the metal anti-grease filters see the assembly instructions.
CARBON-ZEO FILTERS
Under normal conditions, they should be regenerated every 18 months and
replaced after 3 years. To regenerate the filter, follow the following procedure:
- Remove the filter as described in the instructions.
- Insert filters A, B and C (if any) in a domestic oven at 200°C for about 2 hours.
- When the filter has cooled down, refit the 4 filters onto the metal structure of
the filter.
To Next Page
Loading...
General