FATEK FBS-40EAP Series User Manual

【Hardware】
Contents
Chapter 1：Introduction of FATEK FBS Series PLC
1.1 Appearance of Main Unit...............................................................................................................H1-1
1.2 Appearance of Expander/Module.................................................................................................H1-2
1.3 Appearance of Communication Expansion Module ....................................................................H1-4
1.4 List of FBS-PLC Models ................................................................................................................H1-5
1.5 Specifications of Main Unit ............................................................................................................H1-7
1.6 Environmental Specifications ........................................................................................................H1-8
1.7 Connection Diagrams of Various Models.....................................................................................H1-9
1.7.1 NC Control Main Unit..............................................................................................................H1-9
1.7.2 Basic/Advanced Main Unit .....................................................................................................H1-10
1.7.3 Digital I/O Expander................................................................................................................H1-12
1.7.4 Digital I/O Expansion Module.................................................................................................H1-13
1.7.5 High-Density Digital I/O Expansion Module ..........................................................................H1-14
1.7.6 Numeric I/O Expansion Module.............................................................................................H1-14
1.7.7 Analog I/O Expansion Module ...............................................................................................H1-14
1.7.8 Temperature Input Module.....................................................................................................H1-15
1.7.9 Expansion Power....................................................................................................................H1-15
1.7.10 Communication Module (CM)..............................................................................................H1-16
1.7.11 Communication Board (CB).................................................................................................H1-17
1.8 Drawings with External Dimensions .............................................................................................H1-18
Chapter 2：System Architecture
2.1 Single-Unit System of FBS-PLC...................................................................................................H2-1
2.2 Formation of Multiple Units............................................................................................................H2-2
2.2.1 Connection of multiple FBS-PLC...........................................................................................H2-2
2.2.2 Connection of FBS-PLC with host computer or intelligent peripherals................................H2-3
Chapter 3：Expansion of FBS-PLC
3.1 I/O Expansion.................................................................................................................................H3-1

FATEK FBS-40EAP Series Specifications

General

Brand	FATEK
Model	FBS-40EAP Series
Category	Controller
Language	English

Summary

Chapter 1: Introduction of FATEK FBS Series PLC

1.4 List of FBS PLC Models

Provides a comprehensive list of FBS PLC models with their specifications.

1.7 Connection Diagrams of Various Models

Illustrates terminal block connection diagrams for various PLC models.

Chapter 2: System Architecture

Chapter 3: Expansion of FBS-PLC

3.1 I/O Expansion

Covers digital and numeric I/O expansion through units or modules.

Chapter 4: Installation Guide

4.2 Precautions of PLC Installation

Provides essential safety and installation precautions for the PLC.

4.5 Precautions on Construction and Wiring

Lists important precautions for wiring and construction related to the PLC.

Chapter 5: Power Supply Wiring, Power Consumption Calculation, and Power Sequence Requirements

5.1 Specifications of AC Power Sourced Power Supply and Wiring

5.2 Specifications of DC Power Sourced Power Supply and Wiring

Chapter 6: Basic Function Instruction

T (Timer)

Describes the Timer (T) function, its parameters, and operation.

C (Counter)

Explains the Counter (C) function, its parameters, and operation.

SET

RESET

Data Movement Instructions (FUN 8, 9)

Arithmetic Operations (FUN 11-16)

Comparison Instruction (FUN 17)

Logical Operations (FUN 18, 19)

Chapter 7: Advanced Function Instructions

Flow Control Instructions (FUN22, FUN65-71)

Instructions for managing program flow, including loops, jumps, and subroutines.

Arithmetical Operation Instructions (FUN23-32)

Instructions for performing arithmetic operations like addition, subtraction, multiplication, division.

Logical Operation Instructions (FUN35-36)

Comparison Instruction (FUN37)

Compares data between registers and sets flags based on the result.

Data Movement Instructions (FUN40-50, FUN160)

Instructions for moving, shifting, and converting data between registers and tables.

Shifting／Rotating Instructions (FUN51-54)

Code Conversion Instructions (FUN55-64)

Instructions for converting data between different codes like BIN, BCD, Gray, ASCII, Hex.

I/O Instructions (FUN74-86)

Instructions for handling input/output operations and special I/O modules.

Cumulative Timer Instructions (FUN87-89)

Watchdog Timer Instructions (FUN90-91)

Instructions for setting and resetting the watchdog timer for system safety.

High Speed Counter / Timing (FUN92-93)

Instructions for hardware high-speed counters and timers.

Slow Up / Slow Down Instructions (FUN95)

Table Instructions (FUN100-114)

Instructions for manipulating data stored in tables (move, compare, sort, etc.).

Matrix Instructions (FUN120-130)

Instructions for performing operations on data arranged in matrix format.

NC Positioning Instructions (FUN140-143)

Instructions for controlling NC positioning operations.

Enable/Disable Instructions (FUN145-146)

Communication Instructions (FUN150-151)

Instructions for establishing communication links, including Modbus.

Data Movement Instructions2 (FUN160)

Floating Point Number Operations (FUN200-213)

Instructions for floating-point arithmetic, conversions, and comparisons.

Chapter 8: Step Instruction Description

8.1 The Operation Principle of Step Ladder Diagram

Explains the basic operation and structure of step ladder diagrams.

8.2 Basic Formation of Step Ladder Diagram

8.3 Introduction of Step Instructions: STP, FROM, TO and STPEND

Introduces essential step instructions for controlling process sequences.

8.4 Notes for Writing a Step Ladder Diagram

Appendix 2: FBs BDAP User’s Manual

Appendix -5

1.5.1 In and out of FUN functions