FATEK FBs-40MC Series User Manual

【Hardware】
Contents
Chapter 1：Introduction of FATEK FBS Series PLC
1.1 Appearance of Main Unit...............................................................................................................H1-1
1.2 Appearance of Expander/Module.................................................................................................H1-2
1.3 Appearance of Communication Expansion Module ....................................................................H1-4
1.4 List of FBS-PLC Models ................................................................................................................H1-5
1.5 Specifications of Main Unit ............................................................................................................H1-7
1.6 Environmental Specifications ........................................................................................................H1-8
1.7 Connection Diagrams of Various Models.....................................................................................H1-9
1.7.1 NC Control Main Unit..............................................................................................................H1-9
1.7.2 Basic/Advanced Main Unit .....................................................................................................H1-10
1.7.3 Digital I/O Expander................................................................................................................H1-12
1.7.4 Digital I/O Expansion Module.................................................................................................H1-13
1.7.5 High-Density Digital I/O Expansion Module ..........................................................................H1-14
1.7.6 Numeric I/O Expansion Module.............................................................................................H1-14
1.7.7 Analog I/O Expansion Module ...............................................................................................H1-14
1.7.8 Temperature Input Module.....................................................................................................H1-15
1.7.9 Expansion Power....................................................................................................................H1-15
1.7.10 Communication Module (CM)..............................................................................................H1-16
1.7.11 Communication Board (CB).................................................................................................H1-17
1.8 Drawings with External Dimensions .............................................................................................H1-18
Chapter 2：System Architecture
2.1 Single-Unit System of FBS-PLC...................................................................................................H2-1
2.2 Formation of Multiple Units............................................................................................................H2-2
2.2.1 Connection of multiple FBS-PLC...........................................................................................H2-2
2.2.2 Connection of FBS-PLC with host computer or intelligent peripherals................................H2-3
Chapter 3：Expansion of FBS-PLC
3.1 I/O Expansion.................................................................................................................................H3-1

FATEK FBs-40MC Series Specifications

General

Brand	FATEK
Model	FBs-40MC Series
Category	Controller
Language	English

Summary

Chapter 1: Introduction of FATEK FBS Series PLC

1.4 List of FBS PLC Models

Comprehensive list of available FBS PLC models with their specifications.

1.5 Specifications of Main Unit

Chapter 4: Installation Guide

4.2 PLC Installation Precautions

Safety and best practices for installing the PLC hardware.

4.5 Precautions on Construction and Wiring

Guidelines for safe and effective wiring practices.

Chapter 5: Power Supply Wiring, Power Consumption Calculation, and Power Sequence Requirement

5.1 Specifications and Wiring of AC Power Sourced Power Supply

Information on AC power supply options and wiring diagrams.

5.2 Specifications and Wiring of DC Power Sourced Power Supply

Information on DC power supply options and wiring diagrams.

5.3 Residual Capacity of Main/Expansion Unit & Current Consumption of Expansion Module

Chapter 6: Digital Input (DI) Circuit

6.1 Specifications of Digital Input (DI) Circuit

Chapter 7: Digital Output (DO) Circuit

7.1 Specifications of Digital Output Circuits

7.5 Output Device Protection and Noise Suppression in DO Circuit

Chapter 8: Test Run, Monitoring and Maintenance

8.1 Inspection after Wiring and Before First Time Power on

Pre-operation checks and inspections after wiring.

8.2 Test Run and Monitoring

Steps for conducting test runs and monitoring PLC operations.

8.3 LED Indicators on PLC Main Unit and Troubleshooting

Explanation of LED indicators and common troubleshooting steps.

8.4 Maintenance

Chapter 2 FBS-PLC Memory Allocation

2.1 FBS-PLC Memory Allocation

2.2 Digital and Register Allocations

Allocation of digital and register data types, symbols, and ranges.

2.3 Special Relay Details

2.4 Special Registers Details

Chapter 3 FBS-PLC Instruction Lists

3.1 Sequential Instructions

3.2 Function Instructions

Categorizes and describes basic and advanced function instructions.

Chapter 5 Description of Function Instructions

5.1 The Format of Function Instructions

Explains the structure of function instructions including input, operand, and output.

5.2 Use Index Register(XR) for Indirect Addressing

How to use index registers for indirect addressing in function instructions.

5.3 Numbering System

Chapter 6 Basic Function Instructions

T (Timer)

Details on Timer instructions, time bases, and operation.

C (Counter)

Details on Counter instructions, preset values, and operation.

Master control loop start (FUN0)

Master control loop end (FUN01)

Bit shift (FUN06)

Up/down counter (FUN07)

Instruction for up/down counting with 2-phase inputs.

Move (FUN08)

Moves data from a source register to a destination register.

Addition (FUN11)

Subtraction (FUN12)

Multiplication (FUN13)

Chapter 7 Advanced Function Instructions

Division (FUN14)

Compare (FUN17)

Compares two data and outputs results to function outputs.

Logical and (FUN18)

Logical or (FUN19)

Flow control instructions1 (FUN22)

Arithmetical operation instructions (FUN23～32)

Instructions for arithmetic operations like ADD, SUB, MUL, DIV.

Logical operation instructions (FUN35～36)

Instructions for logical operations like AND, OR, XOR.

Comparison instruction (FUN37)

Data movement instructions1 (FUN40～50)

Instructions for moving and manipulating data between registers.

Shifting／Rotating instructions (FUN51～54)

Instructions for bit shifting and rotating operations.

Code conversion instructions (FUN55～64)

Instructions for converting data between formats like BIN, BCD, ASCII.

Flow control instructions2 (FUN65～71)

Instructions for program flow control like MC, SKP, CALL, JMP.

I／O instructions (FUN74～86)

Cumulative timer instructions (FUN87～89)

Watchdog timer instructions (FUN90～91)

Instructions for setting and resetting the watchdog timer.

High speed counting／timing (FUN92～93)

Instructions for high-speed counting and timing operations.

Slow up／Slow down instructions (FUN95)

Table instructions (FUN100～114)

Instructions for manipulating data in tables, like MOV, SORT, COMPARE.

Matrix instructions (FUN120～130)

Instructions for processing data in matrix format.

NC positioning instructions (FUN139～143)

Enable／Disable instructions (FUN145～146)

Communication instructions (FUN150～151)

Instructions for communication protocols like Modbus and ASCII.

Data movement instructions2 (FUN160)

Floating Arithmetical operation instructions(FUN200～213)

Instructions for arithmetic operations on floating-point numbers.

Chapter 8 Step Instruction Description

8.1 The Operation Principle of Step Ladder Diagram

8.2 Basic Formation of Step Ladder Diagram

Describes the formation of step ladder diagrams: single path, divergence, convergence.

8.3 Instruction of Step Introduction: STP, FROM, TO, and STPEND

Details the STP, FROM, TO, and STPEND instructions for step control.

8.4 Notes for Writing a Step Ladder Diagram

Important notes and considerations for writing step ladder programs.

Appendix: FB-DAP Simple Human Machine Interface

1.2 Important points before operation

1.3 The Main Functions of FBS-DAP

Overview of the primary functions and capabilities of the FBS-DAP.

1.4 Setter Functions of General Information

1.5 FUN Functions

1.7 Special message display function