FE PETRO STP150B++ - Standard Models

9
Approximate STP / IST Specications
Operating
Pressure (PSI)
PMA
Length (in)
S.F.
Amps
Locked
Rotor Amps
Winding Resistance
Model Description R-B R-O B-O
STP33* 208 / 230 V, 60 Hz, 1 ph 27 16 3.1 11 27 19 8
STP75* 208 / 230 V, 60 Hz, 1 ph 30 18.25 6.1 27 20 17 3
STP150* 208 / 230 V, 60 Hz, 1 ph 32 21 10.5 39 15 13 2
STPH150* 208 / 230 V, 60 Hz, 1 ph 45 21.75 10.5 39 15 13 2
STP200+ 208 / 230 V, 60 Hz, 1 ph 36 23.75 11.4 41 4.6 3 1.8
STPH200+ 208 / 230 V, 60 Hz, 1 ph 46 24.5 11.4 41 4.6 3 1.8
STP75B++ 200 / 250 V, 50 Hz, 1 ph 37 20.5 5.6 23 27 23 4
STP150B++ 200 / 250 V, 50 Hz, 1 ph 38 22.75 10.2 28 16 13 3
STPH150B++ 200 / 250 V, 50 Hz, 1 ph 48 23.25 10.2 28 16 13 3
STP200B‡ 200 / 250 V, 50 Hz, 1 ph 37 25.75 10.9 36.5 5.5 3.5 2
STPH200B‡ 200 / 250 V, 50 Hz, 1 ph 44 26.25 10.9 36.5 5.5 3.5 2
STP75C 380-415 V, 50 Hz, 3 ph** 37 19.75 2.1 10 29 29 29
STP150C 380-415 V, 50 Hz, 3 ph** 38 21.75 3.4 14 14 14 14
STPH150C 380-415 V, 50 Hz, 3 ph** 48 22 3.4 14 14 14 14
STP200C 380-415 V, 50 Hz, 3 ph** 37 23.5 4.1 22.5 11.6 11.6 11.6
STPH200C 380-415 V, 50 Hz, 3 ph** 44 24 4.1 22.5 11.6 11.6 11.6
IST / STPVS2^ 190 V, 70 Hz, 3 ph† 24-42 20 6.7 N / A 2.5 2.5 2.5
ISTVS4 / STPVS4^^ 190 V, 70 Hz, 3 ph† 24-42 25 14.4 N / A 1.2 1.2 1.2
Symbol Key
* Use a 15 µF, 370 V, single phase, 60 Hz capacitor
+ Use a 40 µF, 370 V, single phase, 60 Hz capacitor
++ Use a 15 µF, 440 V, single phase, 50 Hz capacitor
‡ Use a 40 µF, 440 V, single phase, 50 Hz capacitor
† 190 V, 70 Hz, 3 ph power to variable speed units is output from IST-VFC or MagVFC only (VFC’s are powered
by 200-250 V, 50 or 60 Hz, single or 3 phase input)
^ Use with IST-VFC or MagVFC controller only, No Capacitor
^^ Use with MagVFC controller only, No Capacitor (3 phase input is required for full VS4 output))
** No capacitor is used with 3 phase pump motor assemblies
Note: The models listed in the table above may contain (ANZ) for ANZEX certied pumps, or (ATX) for ATEX certied
pumps.
Warning
FE Petro’s STPs are designed for use with motor fuels, and they are UL listed for blend
concentrations of:
Standard Models AG (Alcohol / Gasoline) Models
0% - 15% ethanol or methanol and gasoline 0% - 85% ethanol or methanol and gasoline
20% MTBE with 80% gasoline 20% MTBE with 80% gasoline
20% ETBE with 80% gasoline 20% ETBE with 80% gasoline
17% TAME with 83% gasoline 17% TAME with 83% gasoline
Diesel, fuel oil, avgas, jet fuel, or kerosene may also be used with our PMAs. The maximum liquid
viscosity for a product is 70 S.S.U. at 60° F.
Using our PMA in liquids other than those mentioned above has not been tested. The reaction of
other liquids with seals and wetted surfaces of the pump is unknown. A hazardous situation may
result from using other liquids with our pump.