Fender STAGE 100 User Manual

STAGE 100/160
STAGE 100 p/n 022-6700-010 (120V)
STAGE 160 p/n 022-6800-010 (120V)
SERVICE MANUAL
CONTENTS:
Notices
Specifications
Parts lists:
PCB assembly
Chassis assembly
Cabinet assembly
End item
Service diagrams
Assembly drawings
Fender Musical Instruments Corp. 7975 North Hayden Road Scottsdale, AZ 85258
STAGE 100/160
(This is the model name for warranty claims)
SERVICE MANUAL
JUNE 1999
IMPORTANT NOTICE:
The information contained herein is CONFIDENTIAL and PROPRIETARY to Fender Musical Instruments Corp. It is
disclosed solely for use by qualified technicians for purposes of equipment maintenance and service. It is not to be
disclosed to others without the expressed permission of Fender Musical Instruments Co. All specifications subject to
change without notice.
For warranty repair service, only Fender specified part numbers are to be used. It is recommended they also be used
for post-warranty maintenance and repair.
Parts marked with an asterisk (
*
) indicate the required use of that specific part. This is necessary for RELIABILITY and
SAFETY requirements. DO NOT USE A SUBSTITUTE!
A coded naming convention is used in the description of certain parts. The codes and what they mean are as follows:
CAPACITOR CODES HARDWARE CODES
CAP AE = Aluminum Electrolytic BLX = Black Oxide
CAP CA = Ceramic Axial CR = Chrome Plated
CAP CD = Ceramic Disk HWH = Hex Washer Head
CAP MPF = Metalized Polyester Film M = Machine Screw
CAP MY = Mylar NI = Nickel Plated
CAP PFF = Polyester Film/Foil OHP = Oval Head Phillips
PB = Particle Board
RESISTOR CODES
PHP = Pan Head Phillips
PHPS = Pan Head Phillips Sems
RES CC = Carbon Comp SMA = Sheet Metal "A" Point
RES CF = Carbon Film SMB = Sheet Metal "B" Point
RES FP = Flame Proof SS = Stainless Steel
RES MF = Metal Film TF = Thread Forming
RES WW = Wire Wound ZI = Zinc Plated
1

Fender STAGE 100 Specifications

General

Power	100 watts
Channels	2
Reverb	Yes
Effects Loop	Yes
Type	Solid State
Speaker Type	Fender Special Design
Channel Types	Clean, Drive
Effects	Reverb
Weight	40 lbs
Speaker	1x12"
Controls	Gain, Volume, Treble, Mid, Bass, Reverb
Outputs	Line Out
Dimensions	20.5" x 19.5" x 10.5" (52.07 cm x 49.53 cm x 26.67 cm)

Summary

Specifications and Parts List - PCB

PCB Capacitors

Lists capacitor components used on the printed circuit board.

Parts List - PCB Continued

PCB Resistors

Lists resistor components used on the printed circuit board.

Parts List - Chassis and Cabinet

Service Diagram - Schematic

Power Supply and Wiring Diagram

Details power supply connections and primary wiring for various voltages.

High and Low Voltage Circuits

Illustrates the high and low voltage supply circuits.

Output Power and Test Conditions

Specifies output power and key test points with conditions.

Service Diagram - PCB Assembly Layout

Front Panel and Input/Output Layout

Shows PCB layout for front panel controls, inputs, and outputs.

Reverb, Footswitch, and Speaker Connections

Channel Select and Drive Circuitry

Depicts PCB layout for channel select and drive circuits.

Chassis Assembly Exploded View

Chassis Component Identification

Identifies major chassis parts with labels and part numbers.

Chassis Hardware and Wiring

Stage 100 Chassis Assembly Details

Stage 100 Chassis Components

Lists specific components for the Stage 100 chassis.

Stage 100 Chassis Hardware

End Item Assembly - Stage 100

Cabinet and Grille Components

Speaker and Reverb System Components