Installation & Operating Instructions
ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı
Page 3
www.fptgroup.com
Fenner is a registered trademark of J.H. Fenner & Co. Limited
CONTENTS
ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı
Page 2
www.fptgroup.com
Fenner is a registered trademark of J.H. Fenner & Co. Limited
Installation & Operating Instructions
1. I
NTRODUCTION 4
1.1. Important safety information 4
1.2. Electromagnetic Compatibility (EMC) 4
2. GENERAL INFORMATION AND RATINGS 5
2.1. Identifying the drive by model number 5
2.2. Drive model numbers 5
3. MECHANICAL INSTALLATION 6
3.1. General 6
3.2. Mechanical dimensions and mounting 6
3.3. Enclosure mounting 6
4. POWER WIRING 7
4.1. Grounding the Drive 7
4.1.1. Grounding Guidelines 7
4.2. Wiring Precautions 7
4.3. Connection Diagram 8
4.4. Drive and motor connections 8
4.5. Motor Terminal Box Connections 8
5. CONTROL WIRING 9
5.1. Control terminal connections 9
5.2. RJ45 Data Connection 9
6. OPERATION 9
6.1. Managing the keypad 9
6.1.1. Changing Parameters 10
6.1.2. Reset Factory Default Settings 10
6.2. Terminal Control 10
6.3. Keypad Control 10
7. PARAMETERS 11
7.1. Standard parameters 11
7.2. Extended parameters 12
7.2.1. Parameter group zero access and
navigation 14
8. ANALOG AND DIGITAL INPUT
CONFIGURATIONS 15
8.1. Terminal mode (P-12 =0) 15
8.2. Keypad mode (P-12 = 1 or 2) 16
8.3. MODBUS control mode (P12 = 3 or 4) 17
8.4. User PI control mode (P-12 = 5 or 6) 17
9. TROUBLESHOOTING 18
9.1. Fault messages 18
10.TECHNICAL DATA 18
10.1. Environmental Data 18
10.2. Rating tables 19
10.3. Maximum supply ratings for UL
compliance: 19
Fenner QD:E Easy Start Up Guide 20
Declaration of Conformity:
ERIKS Industrial Services Ltd hereby states that the Fenner
QD:E Series product range is CE marked for the low voltage
directive and conforms to the following harmonised European
directives:
EN 61800-5-1: 2003 Adjustable speed electrical power
drive systems. Safety requirements.
Electrical, thermal and energy.
EN 61800-3 2nd Adjustable speed electrical
Ed: 2004 power drive systems. EMC
requirements and specific test
methods
EN 55011: 2007 Limits and Methods of measurement
of radio disturbance characteristics of
industrial, scientific and medical (ISM)
radio-frequency equipment (EMC)
Company Information
Address: ERIKS Industrial Services Ltd
Amber Way
Halesowen
West Midlands
B62 8WG
Email: sales@ftpgroup.com
Website: www.ftpgroup.com
All rights reserved. No part of this User Guide may be
reproduced or transmitted in any form or by any means,
electrical or mechanical including photocopying, recording or
by any information storage or retrieval system without
permission in writing from the publisher.
Copyright ERIKS Industrial Services Ltd ©•2008
The manufacturer accepts no liability for any consequences
resulting from inappropriate, negligent or incorrect installation,
or adjustment of the optional operating parameters of the
drive or from mismatching of the drive to the motor.
The contents of this User Guide are believed to be correct at
the time of printing. In the interest of a commitment to a
policy of continuous improvement, the manufacturer reserves
the right to change the specification of the product or its
performance or the contents of the User Guide without notice.
All Fenner QD Series products carry a 2-year warranty, valid
from the date of manufacture. This date is clearly visible on
the product rating label.
This User Guide is for use with V1.02 Software.
User Guide Issue 1.01
NOTE
ERIKS reserves the right to modify the characteristics of its products at any time in order to incorporate technological developments. The information contained in this
document may therefore be changed without notice.
To Next Page
Loading...
