Ferm OTM1005 - Technical Data; Noise and Vibration

5
EN
aftermountingtheaccessories.Ifthemachine
vibrates strongly, immediately switch off the
machine, remove the mains plug from the
mains, and try to solve the problem.
• Makesurethattheworkpieceisproperly
supported or fixed.
• Wearsafetygoggles.Wearhearingprotection.
Wearadustmask.Ifnecessary,useother
protective means, such as safety gloves,
safety shoes, etc. Risk of personal injury.
• Keepbystandersawayfromtheworkarea.
Makesurethatallpersonsintheworkareawear
protectiveequipment.Riskofpersonalinjury.
• Keepthemainscableawayfromtherotating
accessory.Ifthemainscabletouchesthe
rotating accessory, your hands or arms may
come in contact with the accessory. Risk of
personal injury.
• Holdthemachinebytheinsulatedgripping
surfaces where the accessory may contact
hiddenwiringorthemainscable.Ifthe
accessory contacts a ‘live’ wire, the exposed
metal parts of the machine can also become
‘live’. Risk of electric shock.
• Donotusethemachinewhilecarryingitat
your side. Risk of personal injury.
• Donotusethemachinenearflammable
materials. Risk of fire.
• Bewarethattheaccessorycontinuesto
rotate for a short period after switching off
themachine.Donotattempttobringthe
accessory to a standstill yourself.
• Neverputthemachinedownonatableora
workbench before it has been switched off.
• Regularlycleantheventilationslots.Riskof
electric shock.
Electrical safety
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
• Donotusethemachineifthemainscableor
the mains plug is damaged.
• Onlyuseextensioncablesthataresuitablefor
the power rating of the machine with a minimum
thickness of 1.5 mm
2
.Ifyouuseaextension
cable reel, always fully unroll the cable.
Mains plug replacement (UK only)
Ifthemoulded3-pinplugattachedtotheunitis
damaged and needs replacing, it is important
that it is correctly destroyed and replaced by an
approvedBS1363/3Afusedplugandthatthe
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue neutral
brown live
As the colours of the wires in the mains cable
of the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- Thewirewhichiscolouredbluemustbe
connected to the terminal which is marked
with the letter N or coloured black.
- Thewirewhichiscolouredbrownmustbe
connected to the terminal which is marked
withtheletterLorcolouredred.
Technical data
oTm1005
Mains voltage V~ 230
Mains frequency Hz 50
Power input W 280
No-load speed min-1 11,000 - 20,000
Weight kg 1.5
Noise and vibration
oTm1005
Sound pressure (Lpa) dB(A) 85
Acoustic power (Lwa) dB(A) 96
Uncertainty (K) dB(A) 3
Vibration (sanding on wood) m/s
2
4.2
Vibration (sawing in wood) m/s
2
7.3
Vibration (scraping in wood) m/s
2
8.1
Vibration (sawing in steel) m/s
2
5,6
Uncertainty (K) m/s
2
1.5
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with
astandardisedtestgiveninEN60745;itmaybe
used to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- usingthetoolfordifferentapplications,orwith
different or poorly maintainted accessories,