EasyManua.ls Logo

FERREX Z1G-DS-65H - User Manual

FERREX Z1G-DS-65H
26 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PRODUCED IN CHINA FOR:
GB
IE
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly. In
the event of product failure within its intended use over the course of the
first 3 years after date of purchase, we will remedy the problem as quickly
as possible once it has been brought to our attention. In the unlikely event
of such an occurrence, or if you require any information about the product,
please contact us via our helpline support services, details of which are to be
found both in this manual and on the product itself.
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH.
ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE.
Visit us at www.aldi.com
AFTER SALES SUPPORT
802984
GB IE
support@coreservice.co.uk
MODEL:
Z1G-DS-65H
01/2021
+44(0) 1904727501
+353(0) 019022605
3
YEAR
WARRANTY
User Manual
DEMOLITION BREAKER
Original User Manual

Table of Contents

Questions and Answers

  • J
    James WernerAug 7, 2025
    Why is the chiselling output decreasing on my FERREX Z1G-DS-65H?
    • J
      James LaraAug 7, 2025
      If your FERREX Power Tool's chiselling output is significantly decreasing, several factors could be at play. First, make sure you're using a sharp bit; a dull bit can drastically reduce performance, so try using a new one. Also, check the pressure you're applying to the device; excessive pressure can hinder its effectiveness, so reduce the pressure. Adjust the blow count to a higher setting. If the lubricating grease is depleted, replenish it. Lastly, ensure you're working with hard materials, as softer materials can diminish the device's chiselling capability.
  • G
    Gary StevensAug 15, 2025
    What to do if my FERREX Power Tool won't turn on?
    • F
      ftaylorAug 15, 2025
      If your FERREX Power Tool won't switch on, there are a few things to investigate. Begin by verifying that the device is properly connected to a power source. Check the cables, plugs, and the power supply. If the power supply is OK, the carbon brushes may be worn. In this case, have the device repaired by a qualified expert. It's also possible that the motor is defective, which would also require professional repair.
  • M
    Mr. Thomas KelleyAug 27, 2025
    How to fix bit dropping out of FERREX Z1G-DS-65H Power Tool?
    • T
      Timothy MitchellAug 27, 2025
      If the bit keeps dropping out of your FERREX Power Tool, it's likely that the bit holder isn't locking correctly. To resolve this, try re-inserting the bit into the bit holder, ensuring it is properly seated.

Summary

Overview

Scope of delivery;device components

General information

Reading and storing the operating manual

Instructions on reading and storing the manual for future reference.

Proper use

Defines intended use, prohibits misuse, and states it is not a toy.

Residual risks

Outlines potential health/injury risks from vibration, flying parts, and toxic materials.

Explanation of symbols

Safety

Safety notes

Provides general safety warnings and instructions for power tools, emphasizing careful reading.

General safety notes for power tools

General advice for power tools, stressing instruction reading and retention.

Workplace safety

Guidelines for safe work area, avoiding explosive atmospheres, and keeping bystanders away.

Electrical safety

Instructions on plug matching, avoiding grounded surfaces, and protection from rain.

Personal safety

Advice on alertness, PPE use, preventing unintentional starts, and maintaining balance.

Using and handling the power tool

Guidance on tool use, overload prevention, power disconnection, child safety, and maintenance.

Service

Recommendations for servicing by qualified personnel using identical replacement parts.

Before first use

Check the device and scope of delivery

Instructions to check device and components for completeness and damage before first use.

Operation

Selecting the right bit

Guidance on choosing between a pointed bit for hard materials and a flat bit for marking.

Inserting the bit

Step-by-step instructions for securely inserting the bit into the tool holder.

Setting the bit position

Procedure for adjusting the inserted bit's position using the adjusting sleeve.

Adjusting the extra handle

Steps to loosen, move, and retighten the extra handle for optimal positioning.

Presetting the blow count

Instructions on setting the desired blow count using the selector.

Turning the device on and off

Detailed steps for connecting to power, operating the main switch, and using the lock switch.

Removing the bit

Instructions for safely removing the bit, including cooling and using gloves.

Handling the device

Working in horizontal position

Guidance on gripping the tool correctly for horizontal operation, using main and extra handles.

Working in vertical position

Instructions for gripping the main handle with both hands for vertical operation, noting vibration damping.

Cleaning and maintenance

Cleaning

Steps for cleaning device housing and bit after use, including shaft greasing.

Maintenance

Details on greasing gears and changing carbon brushes.

Inspection

Storage

Transport

Troubleshooting

Technical data

Noise;vibration information

Disposal

Disposing of packaging

Instructions for disposing of packaging materials according to type, using recycling bins.

Dispose of old electrical device

Legal obligation to dispose of old electrical devices separately for professional recycling.

Declaration of conformity

FERREX Z1G-DS-65H Specifications

General IconGeneral
BrandFERREX
ModelZ1G-DS-65H
CategoryPower Tool
LanguageEnglish

Related product manuals