Ferris F800X Series - User Manual

Other manuals for Ferris F800X Series

Dealer Service Manual64 pages

Questions and Answers

K
Kevin JonesSep 8, 2025
Why does my Ferris F800X Lawn Mower have excessive mower vibration?
- R
  romerotonySep 8, 2025
  If your Ferris Lawn Mower has excessive mower vibration, it could be that the blade mounting bolts are loose, so tighten them to 70 ft.lbs (94 Nm). The mower blades, arbors, or pulleys might be bent, so check and replace as necessary. The mower blades could be out of balance, so remove, sharpen, and balance them. Also, ensure the belt is installed correctly, and reinstall if needed.
J
James JenningsAug 23, 2025
Why does my Ferris Lawn Mower engine start hard or run poorly?
- J
  James RiveraAug 23, 2025
  If your Ferris Lawn Mower engine starts hard or runs poorly, the fuel mixture might be too rich, so try cleaning the air filter. Also, there might be air in the fuel system, so prime the fuel system.
C
Christina Walker MDAug 25, 2025
Why is my Ferris F800X Lawn Mower rider drive belt slipping?
- R
  Ronald PowellAug 25, 2025
  If your Ferris Lawn Mower drive belt slips, it could be due to pulleys or the belt being greasy or oily, so clean as required. The tension might also be too loose, so adjust the spring tension. If the belt is stretched or worn, replace it.
B
Brad RichAug 26, 2025
What to do if my Ferris F800X is scalping?
- L
  lisastewartAug 26, 2025
  If your Ferris Lawn Mower is scalping, it could be due to several reasons. The lawn might be uneven, so consider rolling or leveling it. The mower deck cutting height might be too low, so raise it. You might be going too fast, so slow down. The deck might not be leveled correctly, so level it. Finally, the tire pressure could be low or uneven, so check and inflate the tires.
K
kevin84Aug 27, 2025
How to prevent streaking with my Ferris F800X Lawn Mower?
- K
  Kayla JacksonAug 28, 2025
  If your Ferris Lawn Mower is streaking, it might be because the blades are not sharp, so sharpen them. They might also be worn down too far, so replace them. Ensure you are mowing at FULL throttle, and that your ground speed isn't too fast, so slow down. The deck could be plugged with grass, so clean it out. Make sure you're overlapping cutting rows enough, including when turning.
B
Brian SheaSep 22, 2025
Why does my Ferris F800X Lawn Mower engine shut off when I move the ground speed control levers?
- E
  Elizabeth RamseySep 22, 2025
  If your Ferris Lawn Mower engine shuts off when the operator pulls the ground speed control levers out of the NEUTRAL position, the mower deck might not be positioned in either the Operating or Service position, so position the mower deck in the Operating or Service position. The parking brake might also be engaged, so disengage it. Also, ensure the operator is sitting in the seat.
A
Adam MartinezSep 16, 2025
What to do if my Ferris Lawn Mower brake will not hold?
- R
  Robert HudsonSep 16, 2025
  If your Ferris Lawn Mower brake will not hold, it could be incorrectly adjusted, so see Brake Adjustment. The brake pads may also be worn, so replace them with new ones.
W
williamsonsusanSep 18, 2025
Why does my Ferris F800X Lawn Mower mower not engage?
- C
  connercourtneySep 18, 2025
  If your Ferris Lawn Mower mower does not engage, it could be due to electrical wiring damage, so locate and repair the damaged wire. The battery voltage might be too low, so recharge the battery and check the alternator. Also, the mower deck might not be in the operating position, so lower the deck to the operating position, disengage the PTO switch, then re-engage the PTO switch.
M
melissa33Sep 7, 2025
What to do if my Ferris Lawn Mower engine runs, but rider will not drive?
- J
  Jonathan DoyleSep 7, 2025
  If your Ferris Lawn Mower engine runs, but the rider will not drive, check if the hydraulic release valve(s) are in the “open” position and turn them CLOCKWISE to close. If the belt is broken, see Drive Belt Replacement. If the drive belt slips, see Problem and Cause below. If the brake is not fully released, see authorized service dealer.
H
Henry DawsonSep 4, 2025
How to fix stingers with my Ferris F800X?
- G
  Gabriella RodriguezSep 4, 2025
  If your Ferris Lawn Mower produces stingers, it's often because the blades are not sharp or nicked, so sharpen them. It could also be because the blades are worn down too far, so replace your blades. Ensure the engine speed is at full throttle, and the ground speed is not too fast, so slow down. Also, check if the deck is plugged with grass, and clean it out if necessary.