To Next Page
E
Emily WestSep 8, 2025
What does Error 13 mean on a Ferrotec Controller?
- CCarlos GuzmanSep 8, 2025
Error 13 on the Ferrotec Controller means that there is an invalid pocket detection. This indicates that the gun drive supplies invalid signals.
What does Error 13 mean on a Ferrotec Controller?
Error 13 on the Ferrotec Controller means that there is an invalid pocket detection. This indicates that the gun drive supplies invalid signals.
What does Warning 09 mean on a ferrotec genius Controller?
Warning 09 on the Ferrotec Controller indicates that the data set has already been saved.
What does Error 07 mean on a ferrotec genius?
Error 07 on the Ferrotec Controller indicates that there is no connection to the remote control.
What does Warning 04 mean on a ferrotec genius Controller?
Warning 04 on the Ferrotec Controller indicates that the WATER interlock is open for less than 3 seconds. This means there is an open contact or no voltage between contact A1 and B1 on X110 (factory setting).
What does Error 04 mean on a Ferrotec Controller?
Error 04 on the Ferrotec Controller means that the WATER interlock is open for more than 3 seconds. This indicates an open contact or no voltage between contact A1 and B1 on X110 (factory setting).
What does Error 03 mean on a ferrotec genius?
Error 03 on the Ferrotec Controller means that the VACUUM interlock is open. Check for an open contact or no voltage between contact A2 and B2 on X110 (factory setting).
What does Error 02 mean on a ferrotec genius?
Error 02 on the Ferrotec Controller indicates that the CHAMBER interlock is open. This means there is an open contact or no voltage between contact A3 and B3 X110 (factory setting).
What does Error 01 mean on a ferrotec genius Controller?
Error 01 on the Ferrotec Controller indicates that the XTERN interlock is open. This means there is an open contact or no voltage between contact A4 and B4 on X110 (factory setting).
What does it mean when the Ferrotec Controller displays Error 26?
If the Ferrotec Controller displays Error 26, it means the time for pocket indexing has exceeded, indicating a pocket jam.
Why does my ferrotec genius show Error 18?
Error 18 on the Ferrotec Controller indicates that the ADC Converter for FPS II is out of limits. Possible reasons are a broken filament, fiber optics not in place, emission current too high, or ADC power failure.
Specifies the authorized use and limitations of the controller.
Explains different types of safety warnings and symbols.
Defines common safety symbols used in the manual.
Describes the built-in safety mechanisms of the controller.
Explains the function and testing of the emergency stop.
Warns about specific dangers within the operational zone.
Defines operational zones and potential hazard areas.
Step-by-step instructions for safely powering down the unit.
Details on wiring the controller to other system components.
Provides a visual representation of the electrical connections.
Instructions for proper safety grounding.
Specific steps for connecting the controller.
Steps for initial setup, connection, and checks.
Overview of the control panel and its components.
How to use the left joystick for menu selection.
How to use the right joystick to modify values.
Detailed explanation of the LCD screen and its sections.
Procedure for adjusting the emission current.
Adjusting magnet current for beam deflection.
Setting the magnet current's position.
Setting the magnet current's amplitude.
Basic principles of menu navigation.
How to set and adjust evaporation parameters.
Adjusting the magnet current's beam position.
Defining the operational limits for magnet current.
Adjusting the magnet current's beam amplitude.
Adjusting the high voltage output level.
Setting the maximum allowable emission current.
Setting the frequency of magnet current deflection.
Accessing and using service functions.
Explanation and handling of system error messages.
Explanation and handling of system warnings.
Pinout and configuration for the X110 I/O interface.
Control logic for the High Voltage power supply.
Configuration options for different sweep modes.
Utilizing dwell matrix patterns for energy distribution.
General| Brand | ferrotec |
|---|---|
| Model | genius |
| Category | Controller |
| Language | English |