What to do if my Fimco Paint Sprayer pump will not run?
If your Fimco Paint Sprayer pump isn't running, here's what you should check: * Ensure all wiring is securely connected. * Verify the ON/OFF switch is in the 'on' position. * Inspect the fuse. * Examine the pressure switch for any defects.
Why does the fuse keep blowing on my Fimco Paint Sprayer?
Several factors can cause the fuse to blow in your Fimco Paint Sprayer. Check the following: 1. Ensure the voltage supply is not excessive. 2. Verify the pressure switch is properly adjusted. 3. Inspect the wiring harness for damage or defects. 4. Check if the half-moon & counterweight are sticking. 5. Examine the pressure switch for defects.
What to do if my Fimco Paint Sprayer pump continues to run?
If the pump in your Fimco Paint Sprayer keeps running, consider these potential causes: * Ensure the bypass is completely closed. * Check the system for leaks and repair them. * Inspect for a worn or dirty check valve. * Check for excessive voltage. * Verify the pressure switch is properly adjusted. * Examine the wiring harness for damage or defects.
How to stop pulsating flow (surging) in my Fimco Paint Sprayer?
To address pulsating flow (surging) in your Fimco Paint Sprayer, try the following: * Increase the flow rate, as low flow may cause the pump to surge. * Adjust the spray wand for a larger spray pattern. * Slightly open the bypass (if applicable) to overcome the issue. * Adjust the pressure switch a quarter turn at a time clockwise until surging stops. * Check for a defective pressure switch. * Inspect for leaks or restrictions in the discharge line. * Check for debris in the nozzle orifice. * Ensure the discharge hose isn't too long. * Check for a clogged strainer.
Why does the motor continue to run after discharge is shut off on my Fimco Paint Sprayer?
If the motor continues to run after the discharge is shut off on your Fimco Paint Sprayer, check the following: * Ensure there is product in the supply. * Check for an open bypass valve (if equipped). * Check for low voltage. * Check for leaks in the discharge line. * Check for a defective pressure switch. * Check the system for leaks and repair them.
How to fix a surging pump in my Fimco Paint Sprayer?
To resolve a surging pump issue in your Fimco Paint Sprayer, consider the following: * Adjust the spray wand for a larger spray pattern, as low flow may cause the pump to surge. * Slightly open the bypass (if applicable) to overcome the issue. * Adjust the pressure switch a quarter turn at a time clockwise until surging stops.
What causes low pressure or low flow in my Fimco Paint Sprayer?
If you're experiencing low pressure or low flow with your Fimco Paint Sprayer, here are a few things to investigate: * Check for a clogged strainer. * Ensure proper voltage; try another 12-Volt battery. * Inspect for a worn or dirty check valve.
Read manual, heed warnings, contact Fimco for support, and retain receipt for warranty.
Attach handgun clips, thread pressure gauge, and check vehicle load capacity for filled sprayer.
Ensure tank is clean and free of foreign material. Rinse tank before filling with plain water for testing.
Steps for testing sprayer leaks, adjusting pressure via bypass valve, and confirming spray pattern.
Connect 12V battery leads correctly. Use the On/Off switch to activate the pump.
Initiate spraying by handgun trigger or bypass valve. Adjust pressure using the bypass valve.
Periodically check strainer. Flush system with water and cleaner after use.
Warning against leaving chemicals in pump and importance of flushing pump after each use.
Identifies the pump model as 5281371 and lists available replacement parts with part numbers.
Provides DOs and DON'Ts for pump usage, including cleaning, winterizing, and prohibited substances.
Troubleshooting steps for pump motor not running or failing to prime, checking wiring, fuse, and switches.
Addresses pulsating flow (surging) and motor continuously running after discharge shut-off.
Diagnoses low pressure/flow issues and blown fuses, suggesting checks for voltage, leaks, and wiring.
Details the siphon tube and shut-off valve placement for intake and cleaning access.
Procedure for checking and cleaning the sprayer's intake filter/screen via the shut-off valve.
Diagram showing all sprayer components with reference numbers for identification.
Detailed list of sprayer parts with reference numbers, part numbers, descriptions, and quantities.
Details limited warranty coverage, duration for sprayer and pump, and exclusions.
Instructions on how to obtain warranty service, including notice requirements and contact information.
Outlines available remedies, limitations on implied warranties, and exclusion of incidental damages.
General| Brand | Fimco |
|---|---|
| Model | LG-25-DLX-SP |
| Category | Paint Sprayer |
| Language | English |
To Next Page