What to do if my Fisher & Paykel Dishwasher is leaking water?
If your Fisher & Paykel Dishwasher is leaking water, check the drain hose connection to the waste pipe and reconnect if necessary. Also, ensure the water inlet hose is securely connected. If the water continues to leak, turn off the water and power supplies to the DishDrawer®.
Why are dishes not drying in my Fisher & Paykel DishDrawer DD60?
If your Fisher & Paykel Dishwasher is not drying dishes properly, ensure the dishes are not nesting together. Refill the rinse aid dispenser if it's depleted, and increase the rinse aid setting if it's too low. Also, avoid using the Eco wash programme; instead, select a standard wash programme.
Why Fisher & Paykel DishDrawer® will not open?
If your Fisher & Paykel DishDrawer® won't open, the Childlock feature or the Closed drawer option might be activated. To resolve this, turn off the Childlock by holding down the / button until the symbol disappears from the LCD screen or the light above the / button disappears. You can also press the button to open the DishDrawer®.
What does continuous beeping mean on a Fisher & Paykel DishDrawer DD60?
If your Fisher & Paykel Dishwasher is beeping continuously, it indicates a fault has occurred. Consult the ‘Fault codes’ section for more information.
How to clean stained interior of Fisher & Paykel DishDrawer®?
If your Fisher & Paykel DishDrawer® interior is stained, it may be due to some foods, like tomato-based products. Try pre-rinsing dishes before placing them in the DishDrawer®. Alternatively, using the Rinse programme after adding the dishes may minimise staining.
Why is my Fisher & Paykel DishDrawer® beeping intermittently?
If your Fisher & Paykel DishDrawer® is beeping intermittently, it is likely in pause mode. To resolve this, close the DishDrawer® and press the button.
What to do if my Fisher & Paykel DishDrawer DD60 shows A1: Water Supply error?
If your Fisher & Paykel Dishwasher displays an A1 error related to the water supply, several factors could be the cause. First, ensure that the incoming water pressure and flow rate are adequate. If there is no water in the tub, enter the hardware output mode and run the fill valve to check if the water supply is connected. Also, inspect the hose filters for any blockages and clean them, or replace the fill valve if needed. Make sure there is no foam in the tub. Lastly, verify that the motor rotor is undamaged and replace it if necessary, as it may be damaged.
How to remove water marks from dishes in Fisher & Paykel Dishwasher?
If you find water marks on dishes after using your Fisher & Paykel Dishwasher, it could be due to a few reasons. Check if the rinse aid is depleted and refill the dispenser if needed. If the rinse aid setting is too low, increase it. Also, make sure you are not overloading the DishDrawer® or loading it incorrectly.
Why is my Fisher & Paykel Dishwasher foaming?
If your Fisher & Paykel Dishwasher is foaming, it could be due to using an incorrect amount of detergent, having too much egg in the wash load, or setting the rinse aid too high. Adjust the detergent amount according to the detergent section or manufacturer's instructions. If there is too much egg, increase the amount of detergent. Decrease the rinse aid setting.
Why is my Fisher & Paykel DishDrawer DD60 Dishwasher making excessive motor noise?
If your Fisher & Paykel Dishwasher is making excessive motor noise, the filter plate or spray arm might be incorrectly placed. Refer to the 'Care and cleaning' section for correct placement details. It could also be due to no water in the motor area, which often happens on the first use or after long periods of inactivity. Run the DishDrawer® through a wash programme.
General| Product Category | Dishwasher |
|---|---|
| Installation | Built-In |
| Controls | Touch controls |
| Features | Delay start |
| Color Options | Stainless Steel, White |
| Energy Star Qualified | Yes |
General safety precautions for operating the DishDrawer®, covering usage, children, and materials.
Instructions for safe installation of the DishDrawer®, including qualified technicians and power supply.
Key operational safety points, including pausing before opening and proper loading.
Operation of power, start, pause, and delay start buttons on LCD models.
Step-by-step guide to loading dishes and adding detergent/rinse aid.
Details standard wash programmes, their uses, and temperatures for optimal cleaning.
General advice on loading items for best wash performance.
How to fill and use the detergent dispenser, with important safety warnings.
Procedures for cleaning the drain filter, spray arm, and filter plate.
Step-by-step instructions for cleaning the spray arm and filter plate assembly.
Diagnosing and resolving issues with unclean dishes, foaming, and water leaks.
Troubleshooting steps for when the drawer won't open or the unit won't start.
How to identify fault codes and the general procedure for addressing them.
Detailed list of fault codes F1-F9, their causes, and corrective actions.
Detailed list of fault codes U1, U4, their causes, and corrective actions.
To Next Page
