Why is my Fisher & Paykel Washer not spinning properly?
If your Fisher & Paykel Washer isn't spinning properly, it might be due to an unbalanced load. Try pausing the machine and manually redistributing the clothes inside. Also, make sure the machine is level and doesn't rock, and check for suds buildup.
How to fix a Fisher & Paykel FabricSmart WA1068P that is not turning on?
If your Fisher & Paykel Washer isn't turning on, it could be due to a couple of reasons. First, check if the power is switched on at the wall. Try switching the power off, wait 60 seconds, and then turn it back on. Also, ensure that your household power supply is working by plugging in another electrical appliance to see if it works.
What to do if my Fisher & Paykel FabricSmart WA1068P is not filling with water?
If your Fisher & Paykel Washer isn't filling with water, here are a few things to check: * Make sure both the hot and cold inlet taps are fully turned on. * Inspect the inlet hose filters for any blockages and clear them. * Check if the 'Delay Start' function is activated.
How to stop my Fisher & Paykel Washer from continuously filling with water?
If your Fisher & Paykel Washer is continuously filling, ensure the drain hose is correctly placed in the standpipe or tub. Make sure the standpipe is at least 850 mm but no more than 1200 mm high. To prevent siphoning, ensure the drain hose does not extend more than 20 mm from the end of the hose guide.
What causes a Fisher & Paykel FabricSmart WA1068P Washer to continually go out of balance?
If your Fisher & Paykel Washer is continually going out of balance, the machine may not be level. Make sure the machine is level and does not rock in any direction. Also, ensure an appropriate water level is selected for the load size, or select ‘Auto’ water level.
What causes a small puddle to come from under my Fisher & Paykel Washer?
If there's a small puddle coming from under your Fisher & Paykel Washer, it could be because the water level is too high for the amount of clothes, causing excessive splashing. Large bulky garments, like pillows or duvets, can also cause splashing.
Why is my Fisher & Paykel FabricSmart WA1068P Washer not removing soil effectively?
If your Fisher & Paykel Washer isn't removing soil effectively, consider the following: * Ensure you're using the most appropriate wash cycle for the amount of dirt. * Check the wash water temperature. * Use enough detergent for the load size and soil level, following the manufacturer's recommendations. * Separate light and heavily soiled items. * Avoid overloading the washer by reducing the load size.
How to prevent creasing in my Fisher & Paykel FabricSmart WA1068P Washer?
To minimize creasing in your Fisher & Paykel Washer, try reducing the load size and selecting the ‘Easy Iron’ or ‘Delicate’ cycle. You can also try selecting a lower spin speed and a lower wash temperature for the items. Do not leave wet clothes to sit in the washer or laundry basket.
Why is my Fisher & Paykel FabricSmart WA1068P making banging noises?
If your Fisher & Paykel Washer is making banging noises, it could be due to an out-of-balance load. Try redistributing the load. Also, select a lower water level or wash on the BULKY cycle.
Why does the spin speed sound slower than normal on my Fisher & Paykel FabricSmart WA1068P?
If the spin speed sounds slower than normal on your Fisher & Paykel Washer, it could be because the clothes are unevenly distributed, causing the washer to compensate by lowering the spin speed. Also, the outer wash bowl may still be hot from being filled with hot water, or the washer has slowed the spin speed as a protective measure.
General| Model | WA1068P |
|---|---|
| Type | Top Load Washer |
| Capacity | 10 kg |
| Energy Rating | 4 Stars |
| Energy Star Certified | Yes |
| Color | White |
| Wash Programs | Delicate |
To Next Page
