Flex PE 14-2 150 - Speed Control and Tool Fitting; Setting the Operating Speed; Attaching Tool Holders and Tools

PE 14-2 150, PE 14-1 180
18
Preselecting the speed
 To set the operating speed, move the dial
to the required value.
 Gently press the switch to accelerate the
power tool up to the preselected speed.
`^rqflk>
oáëâ=çÑ=áåàìêó=ÇìÉ=íç=ÇÉëíêìÅíáçå=çÑ=íÜÉ=íççäK=
rëÉ=íÜÉ=~ééêçéêá~íÉ=íççä=Ñçê=íÜÉ=àçÄK
klqb
fÑ=~å=çîÉêäç~Ç=çê=çîÉêÜÉ~íáåÖ=çÅÅìêë=ÇìêáåÖ=
ÅçåíáåìÉë=çéÉê~íáçåI=íÜÉ=éçïÉê=íççä=~ìíçJ
ã~íáÅ~ääó=êÉÇìÅÉë=íÜÉ=ëéÉÉÇ=ìåíáä=íÜÉ éçïÉê=
íççä=Ü~ë=ÅççäÉÇ=Ççïå=~ÇÉèì~íÉäóK
Attaching the tool holder
 Pull out the mains plug.
 Press and hold down the spindle lock (1.).
 Screw the tool holder (Velcro pad, fleece
pad) clockwise onto the spindle and tighten
hand-tight (2.).
 Attach the tool to the tool holder.
 Insert the mains plug into the socket.
 Switch on the polisher (without engaging it)
and run the polisher for approx.
30 seconds. Check for imbalances and
vibrations.
 Switch off the polisher.
Changing the tool holder
 Pull out the mains plug.
 Press and hold down the spindle lock.
 Unscrew tool holder anti-clockwise and
screw it off the spindle.
 Attach new tool holder (see above).
Attaching the tools
`^rqflk>
^íí~ÅÜ=íÜÉ=íççäë=áå=íÜÉ=ÅÉåíêÉ=çÑ=íÜÉ=íççä=ÜçäÇÉêK=
fãÄ~ä~åÅÉë=ã~ó=Ç~ã~ÖÉ=íÜÉ=éçïÉê=íççäK=
qÜÉ ïçêâ=êÉëìäí=ã~ó=ÄÉ=áãé~áêÉÇK
Operating instructions
klqb
tÜÉå=íÜÉ=éçïÉê=íççä=áë=ëïáíÅÜÉÇ=çÑÑI=íÜÉ=íççä=
ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
If using a polishing paste, use the respective
tool for each paste.
On sensitive surfaces (e.g. car paintwork)
do not work aggressively but work at slow
speeds applying low contact pressure.
Sponges can be washed in the washing
machine.
For further information on the manufacturer’s
products go to www.flex-tools.com
.