Fluke Calibration 9500B User Manual (English)

To Next Page

November 2019

All product names are trademarks of their respective companies.

9500B

High Performance Oscilloscope Calibrator

Calibration Manual

Table of Contents3
Introduction7
Contact Fluke Calibration Calibration7
Safety Information8
Product Use8
Specifications8
Routine Maintenance8
- General Cleaning8
- Air Intake Filter8
- Firmware Upgrade10
Model 9500B Test and Selftest13
- Types of Tests13
  - Test Mode13
- Base, Heads, All and Fast Selftest14
- Selftest at Power-On18
- Interface Test19
Printing Selftest Results29
- Introduction29
- Parallel Port (Rear Panel)29
- Printing Setup30
  - Printer Type30
  - Data Formatting31
- Results Printout31
Error Reporting Subsystem31
Error Detection31
Error Messages32
- System Trip Errors32
- Recoverable Errors32
Verification42
Need for Verification42
- Factory Calibration and Traceability42
- Verification on Receipt from the Factory42
- Verification after User-Calibration42
Equipment Requirements42
Interconnections43
Verification Points43
Specification Limits43
Verification Procedure43
9500B Mainframe Verification by Functions43
- Verifying the DC/Square Function: DC Voltage44
- Verifying the DC/Square Function: Square Voltage48
- Verifying the LF Sine Voltage Function51
- Verifying the Time Markers Function54
- Verifying the Load Resistance Measurement Function56
- Verifying the Pulse Width Function59
9510/9530/9550/9560 Head Verification by Functions60
- Verifying the Leveled Sine Function: LF Gain61
- Verifying the Leveled Sine Function: Flatness64
- Verifying the Edge Function71
- Verifying the Load Capacitance Measurement Function (Ε)76
Calibration80
9500B Mainframe Calibration and Active Head™ Calibration80
- Mainframe Unit Calibration80
- Active Head Calibration81
- Other Functions81
- Mainframe Unit Manual Calibration82
The Model 9500B Calibration Mode82
- Mode Selection83
  - Mode' Key83
  - Mode Selection' Screen84
- Selection of Calibration Mode84
- Special Calibration86
- Special Cal: 'Adjust FREQ88
- Mainframe Standard Calibration (BASE CAL)90
- Overview of Calibration Operations92
Standard Calibration - Basic Sequences94
- Aim of Calibration95
- General Calibration Process95
- Target Selection Screen - Selecting Hardware Configurations95
- The Adjustment Screen97
- Calibrating the Model 9500B at Target Values99
- Standard Calibration of AC Functions101
  - Output Frequency Synthesis101
  - Changing the Output Frequency of Target Calibration Points101
- Exit from Base Calibration - Cal Date and Cal Due Date102
Front Panel Base Calibration by Functions105
- Introduction105
- Summary of Calibration Process106
  - General Procedure106
  - Sequencing Calibrations108
- DC/Square - DC Voltage Calibration109
- DC/Square - Square Calibration113
- LF Sine Voltage Calibration117
- Load Resistance Measurement Calibration121
9510/9530/9550/9560 Head Calibration Procedures124
- Levelled Sine Function: LF Gain124
- Levelled Sine Function: HF Calibration126
- Calibrating the Edge Function134
- Calibrating the Timing Markers (9510 Only)146
- Load Capacitance Function Calibration (9510 and 9530 Only)147
- Ω / 1 MΩ Ratio Calibration148
- Exit from Head Calibration150

Need help?

Do you have a question about the Fluke Calibration 9500B and is the answer not in the manual?

Fluke Calibration 9500B Specifications

General

Brand	Fluke Calibration
Model	9500B
Category	Test Equipment
Language	English

Related product manuals

Fluke Calibration 5730A

260 pages

Fluke Calibration 5560A

120 pages

Fluke Calibration 9500B User Manual

Table of Contents

Fluke Calibration 9500B Specifications

Related product manuals