Fluke Calibration 5322A

To Next Page

January 2019

All product names are trademarks of their respective companies.

5322A

Multifunction Electrical Tester Calibrator

Operators Manual

Main Page

Table of Contents5
Introduction9
Safety Information10
- Warnings10
- Symbols12
Contact Fluke Calibration13
Specifications13
Service Information13
Calibrator Functions14
- Function Descriptions14
- Other Features16
Accessories16
- Included Accessories17
- Optional Accessories18
Unpack and Inspect the Product18
Power Considerations18
- Mains Power Cord19
- Mains Voltage19
- Ground the Product20
- Line Power and Fuse20
- Replace the Fuses20
- Select the Line Voltage21
Install the Product in an Equipment Rack21
Switch Power on21
Operation Rules23
Warm-Up Time23
Front-Panel Operation24
- Front-Panel Feature Descriptions24
- Rear-Panel Features28
- Display Features29
Control the Product31
- Select a Function31
- Help31
- Set the Output Signal Value32
- Readings34
- Connection/Disconnection of Output Terminals34
Calibrator Setup Menu35
- Set a General Setup Function35
Factory Settings39
Product Functions40
Set the Low Resistance Source Output40
- Output Selection40
Set the High Resistance Source Output43
- Output Selection44
Set the Ground Bond Resistance Output47
- Use the Ground Bond Resistance Mode48
- Use the Ground Bond Resistance Open Function49
Use the Loop and Line Impedance Function49
- Line and Loop Residual Impedance52
- Set the Compensation of Test Lead Resistance Value58
Use the Leakage Current Function58
- Passive Leakage Current59
- Differential Leakage Current60
- Active Leakage Current (5322A/VLC Only)61
- Substitute Leakage Current Mode63
Use the RCD Test Functions66
- RCD Trip Current Function for Installation Testers66
  - Power Line Voltage69
  - Touch (Contact) Voltage69
- Trip Current Calculation70
- RCD Trip Time for Installation Testers71
  - Power Line Voltage73
  - Touch (Contact) Voltage73
- Output Terminals Reconnection76
- RCD Trip Time for Pats77
AC/DC Voltage Outputs (5322A/VLC Only)78
Measure with the Built-In Multimeter81
- Function Selection82
- Multimeter Input Selection84
- HIPOT LC Function84
- HIPOT Timer Function88
- Flash V (Voltage) Function89
- Flash LC (Leakage Current) Function90
Remote Operation91
Using the IEEE 488 Port for Remote Control91
- IEEE 488 Bus Restrictions91
- Set up the IEEE 488 Port92
Use the USB Port for Remote Control92
- Set up the USB Port93
- Exceptions for USB Remote Control94
5320A Remote Emulation94
Remote Interface Factory Settings94
Command Syntax Information95
- Parameter Syntax Rules95
- Terminators96
- Description of Abbreviations96
- Numeric Output Format97
Supported SCPI Commands97
- SCPI Command Summary98
- System Command Summary110
- Status Command Summary110
- Common Command Summary111
- SCPI Command Details112
  - Using the Output Commands112
  - Using the Source Commands112
- Using System Commands153
- Status Subsystem155
- IEEE 488.2 Common Commands157
- Standard Status Data Structures159
- IEEE 488 Interface Configuration163
Operator Maintenance164
Clean the Ground Bond Resistance and Loop/Line Impedance Relays165
Access the Fuses166
- Line-Power Fuse166
- Measurement Input Fuses166
Clean the Air Filter167
Clean the Exterior168
Product Error Messages169
What to Do in Case of Product Failure172
DUT Calibration Examples172
- Calibrate Continuity Testers173
Calibrate Earth Resistance Testers174
Calibrate Insulation Resistance Testers175
- Calibrate Hand Crank Insulation Testers with the 5 Kv High Resistance Option178
- Calibrate Insulation Resistance Testers with the Resistance Multiplier179
- Calibrate Ground Bond Resistance Testers187
Calibrate Ground Bond Resistance Function in HIPOT Testers189
Calibrate Line Impedance Testers190
Calibrate Loop Impedance Testers192
Calibrate Leakage Current Testers193
- Passive, Differential, and Substitute Leakage Current Calibration193
Calibrate Residual Current Device (RCD) in Installation Testers195
- Calibrate RCD Trip Time195
- Calibrate RCD Trip Current199
Calibrate Residual Current Device (RCD) in Pats (Portable Appliance Tester)200
Calibrate AC and DC Voltage (5322A/VLC Only)202
Calibrate Load Test for Appliance Testers205
Perform Flash Class I and Flash Class II Tests on (PAT) Portable Appliance Testers207
Calibrate Hipots211
- Measure High Voltage with the HV Input211
- Measure High Voltage with the 10 Kv Divider Probe212
- Measure High Voltage with the 80K-40 High Voltage Probe213
- Measure Leakage Current with the 5322A-LOAD214

Other manuals for Fluke Calibration 5322A

Calibration Manual102 pages

Need help?

Do you have a question about the Fluke Calibration 5322A and is the answer not in the manual?

Fluke Calibration 5322A Specifications

General

Manufacturer	Fluke Calibration
Model	5322A
Power Supply	Internal
Product Type	Calibrator
Frequency Range	10 Hz to 1 MHz
Accuracy	Varies by function and range
Power Requirements	100 V to 240 V, 50 Hz/60 Hz
Display	LCD
Resistance Range	0 to 1100 MΩ

Related product manuals

Fluke Calibration 5730A

260 pages

Fluke Calibration 5560A

120 pages

Fluke Calibration 9500B

150 pages

Fluke Calibration 5322A - User Manual

Table of Contents

Other manuals for Fluke Calibration 5322A

Fluke Calibration 5322A Specifications

Related product manuals